Ethernet UTP cables cannot be used.

There are no problems even though the SB/SW refresh device has not been set.

SB/SW uses 512 points of refresh devices.

Use a T-branch repeater module instead of a terminal block.

A terminating resistor must be connected to the interface in order to reduce signal reflections thus preventing the sign

X and Y assignments are as follows.- X0 to XF- Y10 to Y1F

All stations communication error of a slave station.When POWER of the slave station is off, check if 24 V DC has been su

X devices will be assigned as follows. (With this setting, 32 points are occupied per station.) - Station No. 1: X10

For CPU modules with 8192 I/O device points (X/Y0 to 1FFF), X/Y1000 and greater can be set as refresh devices.

Transient transmission is a function that allows communication with programmable controllers in other stations. Communic

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC > Network related products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ Network related products ]

81-90 of Total 110

prev 9 / 11page next

Using Ethernet UTP cables for the CC-Link IE Controller

Ethernet UTP cables cannot be used. More Details >>
- No：23062
- Release Date：2018/09/03 17:31
SB/SW refresh device setting with CC-Link

There are no problems even though the SB/SW refresh device has not been set. More Details >>
- No：23080
- Release Date：2018/09/03 17:31
SB/SW refresh device setting with CC-Link

SB/SW uses 512 points of refresh devices. More Details >>
- No：23081
- Release Date：2018/09/03 17:31
How to relay CC-Link cables

Use a T-branch repeater module instead of a terminal block. More Details >>
- No：23086
- Release Date：2018/09/03 17:31
Terminating resistors for QJ71C24N

A terminating resistor must be connected to the interface in order to reduce signal reflections thus preventing the signal instabilities. More Details >>
- No：22982
- Release Date：2018/09/03 17:31
Assigning X and Y signals of AJ65SBTB1-32DT

X and Y assignments are as follows.- X0 to XF- Y10 to Y1F More Details >>
- No：23034
- Release Date：2018/09/03 17:31
Cause to turn on the ERR LED of a CC-Link master module

All stations communication error of a slave station.When POWER of the slave station is off, check if 24 V DC has been supplied.When POWER is on, check the st... More Details >>
- No：23079
- Release Date：2018/09/03 17:31
Assignment for connecting two CC-Link remote input modules (16-point type) (Remote net Ver.1 mode)

X devices will be assigned as follows. (With this setting, 32 points are occupied per station.) - Station No. 1: X100 to X11F -Station No. 2: X120 to X13... More Details >>
- No：23082
- Release Date：2018/09/03 17:31
- Update：2018/09/26 13:15
Refresh devices

For CPU modules with 8192 I/O device points (X/Y0 to 1FFF), X/Y1000 and greater can be set as refresh devices. More Details >>
- No：23014
- Release Date：2018/09/03 17:31
Transient transmission of the CC-Link IE Controller

Transient transmission is a function that allows communication with programmable controllers in other stations. Communication with programmable controllers i... More Details >>
- No：23016
- Release Date：2018/09/03 17:31

81-90 of Total 110

Inquiries

page top