Set Pr.37 (Speed display) to the speed obtained when operating the machine at the frequency set with Pr.505 (Speed setti

Yes, you can use the setup software (FR-SW3-SETUP-WJ) to set it.

Set Pr.338 to "0" (NET) and Pr.339 to "1" or "2".

You can change the full-scale value by changing Pr.55 (Frequency monitor reference). The initial setting is 60 Hz.

Normally, Pr.80 and Pr.81 are the parameters that can be changed when the operation is stopped in the PU operation mode.

Set the rated motor current to Pr.9. It is the heat protection setting for the motor, and thus the inverter does not shu

It is the standardized Mini-B connector.

Check that the wiring of the terminal 4 and 5 are not reversed.

After setting Pr.79 (Operation mode selection) to "2" and Pr.340 (Communication startup mode selection) to "10", reset t

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-F700

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-F700 ]

111-120 of Total 296

prev 12 / 30page next

Monitor indicator

Set Pr.37 (Speed display) to the speed obtained when operating the machine at the frequency set with Pr.505 (Speed setting reference). (For FR-F700/E700/D700... More Details >>
- No：21716
- Release Date：2018/08/22 16:29
FR-Configurator

Yes, you can use the setup software (FR-SW3-SETUP-WJ) to set it.　　 More Details >>
- No：21711
- Release Date：2018/08/22 16:29
Network operation

Set Pr.338 to "0" (NET) and Pr.339 to "1" or "2". More Details >>
- No：21674
- Release Date：2018/08/22 16:28
Full scale frequency

You can change the full-scale value by changing Pr.55 (Frequency monitor reference). The initial setting is 60 Hz. More Details >>
- No：21672
- Release Date：2018/08/22 16:28
Parameter display setting

Normally, Pr.80 and Pr.81 are the parameters that can be changed when the operation is stopped in the PU operation mode. The "Er4" is a mode designation erro... More Details >>
- No：21335
- Release Date：2018/08/22 16:27
Fault output terminal A, B, and C

Set the rated motor current to Pr.9. It is the heat protection setting for the motor, and thus the inverter does not shutoff immediately at the specified cur... More Details >>
- No：21324
- Release Date：2018/08/22 16:27
Connection cable of FR-Configurator

It is the standardized Mini-B connector. More Details >>
- No：21312
- Release Date：2018/08/22 16:26
Frequency setting signal

Check that the wiring of the terminal 4 and 5 are not reversed. More Details >>
- No：21266
- Release Date：2018/08/22 16:26
CC-Link communication

After setting Pr.79 (Operation mode selection) to "2" and Pr.340 (Communication startup mode selection) to "10", reset the inverter (or power ON again) to st... More Details >>
- No：21256
- Release Date：2018/08/22 16:26
Driving a single-phase motor

No, it cannot. More Details >>
- No：21253
- Release Date：2018/08/22 16:26

111-120 of Total 296

Inquiries

page top