Cause:Wire breakage on the hand signal line. The electronic hand controller(manufactured by TAIYO Ltd.) has failed. Faul

Cause:The Ethernet cable is not connected surely. There are the device etc. which cause the noise and the noise has appl

Cause:Deterioration in the packing. Scaling on the packing. Using a highly permeable cutting oil. An environment that ex

Cause: A stop signal(STOP/STOP2/SKIP) is being input from an external source. The operating right is not given.(IOEN

Cause:Incorrect breaker selection(current capacity/drive purpose, etc.). Leakage current due to electrically conductive

Cause:An air leak/break in the piping. The solenoid bulb has failed. Wire breakage on the hand signal line. Hand signal

Cause:Program error (arithmetic processing, etc.). Teaching operation error. Peripheral equipment is offset. There is a

Cause:The fuse (4A fuse) installed at the bottom of the 24 V power supply circuit in the controller may have blown out.F

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Robots

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Robots

Industrial/Collaborative Robots-MELFA(54)

Vertical type robot(18)
Horizontal type robot(18)
Ceiling mounted, holizontal type robot(18)
Collaborative Robots

FAQ within [ Robots ]

11-18 of Total 18

prev 2 / 2page next

The hand does not move properly (Electric operated hand).

Cause:Wire breakage on the hand signal line. The electronic hand controller(manufactured by TAIYO Ltd.) has failed. Faulty connection in the cables that run ... More Details >>
- No：23177
- Release Date：2018/09/07 16:09
- Category： Vertical type robot , Horizontal type robot , Ceiling mounted, holizontal type robot
The communication fault occurs by the equipment connected to the Ethernet cable inside the robot arm.

Cause:The Ethernet cable is not connected surely. There are the device etc. which cause the noise and the noise has applied to the Ethernet cable. Measures:C... More Details >>
- No：23179
- Release Date：2018/09/07 16:09
- Category： Vertical type robot , Horizontal type robot , Ceiling mounted, holizontal type robot
Breaker trips/overcurrent error occurs.

Cause:Deterioration in the packing. Scaling on the packing. Using a highly permeable cutting oil. An environment that exceeds the IP functionality. Measures:... More Details >>
- No：23175
- Release Date：2018/09/07 16:09
- Category： Vertical type robot , Horizontal type robot , Ceiling mounted, holizontal type robot
In automatic drive mode, the system does not start up or the robot stops during automatic drive.

Cause: A stop signal(STOP/STOP2/SKIP) is being input from an external source. The operating right is not given.(IOENA parameters settings/exclusive input... More Details >>
- No：23171
- Release Date：2018/09/07 16:09
- Update：2018/10/03 14:48
- Category： Vertical type robot , Horizontal type robot , Ceiling mounted, holizontal type robot
The leakage current breaker trips.

Cause:Incorrect breaker selection(current capacity/drive purpose, etc.). Leakage current due to electrically conductive foreign matters(oil/moisture) getting... More Details >>
- No：23173
- Release Date：2018/09/07 16:09
- Category： Vertical type robot , Horizontal type robot , Ceiling mounted, holizontal type robot
The hand does not move properly (air hand).

Cause:An air leak/break in the piping. The solenoid bulb has failed. Wire breakage on the hand signal line. Hand signal line short circuitThe hand IF card ha... More Details >>
- No：23176
- Release Date：2018/09/07 16:09
- Category： Vertical type robot , Horizontal type robot , Ceiling mounted, holizontal type robot
The position becomes offset.

Cause:Program error (arithmetic processing, etc.). Teaching operation error. Peripheral equipment is offset. There is a setting error in the origin position ... More Details >>
- No：23172
- Release Date：2018/09/07 16:09
- Category： Vertical type robot , Horizontal type robot , Ceiling mounted, holizontal type robot
The T/B does not display anything.

Cause:The fuse (4A fuse) installed at the bottom of the 24 V power supply circuit in the controller may have blown out.For the fuse blowout, the emergency st... More Details >>
- No：23184
- Release Date：2018/09/07 16:09
- Category： Vertical type robot , Horizontal type robot , Ceiling mounted, holizontal type robot

11-18 of Total 18

Inquiries

page top