Cause: AC line inside the controller may have detected the abnormalities. Measures: Check that the primary s

Cause:[Occurs only when operating manually]•T/B operation error.[Occurs when operating manually and automatically]•Fault

Cause:Program error (arithmetic processing, etc.). Teaching operation error. Peripheral equipment is offset. There is a

Cause:A servo OFF signal(SRVOFF)is being input from an external source. The operating right is not given.(IOENA paramete

Cause: A stop signal(STOP/STOP2/SKIP) is being input from an external source. The operating right is not given.(IOEN

Cause:The fuse (4A fuse) installed at the bottom of the 24 V power supply circuit in the controller may have blown out.F

Cause:The load conditions exceed the specified values(mass, inertia).The load condition settings are not suitable(HNDDAT

Cause:Unusual noises can be caused by friction between movable parts, deformed parts, foreign matters getting inside, an

Cause:[Occurs only when operating manually]•T/B operation error.•The enabling device input is open.[Occurs when operatin

Cause:CPU has not started up properly.There is no power supply.An instantaneous power cut exceeding the specification le

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Robots > Industrial/Collaborative Robots-MELFA > Vertical type robot

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ Vertical type robot ]

1-10 of Total 18

prev 1 / 2page next

The operation panel does not light up. Although the T/B has got the electricity, the operation of T/B cannot be done.

Cause: AC line inside the controller may have detected the abnormalities. Measures: Check that the primary side’s power supply voltage is being su... More Details >>
- No：23182
- Release Date：2018/09/07 16:09
- Update：2018/10/03 14:52
Brake is not working properly.

Cause:[Occurs only when operating manually]•T/B operation error.[Occurs when operating manually and automatically]•Faulty connection of the cables that run b... More Details >>
- No：23178
- Release Date：2018/09/07 16:09
The position becomes offset.

Cause:Program error (arithmetic processing, etc.). Teaching operation error. Peripheral equipment is offset. There is a setting error in the origin position ... More Details >>
- No：23172
- Release Date：2018/09/07 16:09
The servo-on cannot be performed.

Cause:A servo OFF signal(SRVOFF)is being input from an external source. The operating right is not given.(IOENA parameters settings/exclusive input and outpu... More Details >>
- No：23170
- Release Date：2018/09/07 16:09
In automatic drive mode, the system does not start up or the robot stops during automatic drive.

Cause: A stop signal(STOP/STOP2/SKIP) is being input from an external source. The operating right is not given.(IOENA parameters settings/exclusive input... More Details >>
- No：23171
- Release Date：2018/09/07 16:09
- Update：2018/10/03 14:48
The T/B does not display anything.

Cause:The fuse (4A fuse) installed at the bottom of the 24 V power supply circuit in the controller may have blown out.For the fuse blowout, the emergency st... More Details >>
- No：23184
- Release Date：2018/09/07 16:09
The tip of the robot is vibrating.

Cause:The load conditions exceed the specified values(mass, inertia).The load condition settings are not suitable(HNDDAT and WRKDAT settings are not consiste... More Details >>
- No：23169
- Release Date：2018/09/07 16:09
An unusual noise can be heard (from the robot arm).

Cause:Unusual noises can be caused by friction between movable parts, deformed parts, foreign matters getting inside, and defects in belt tension.An unusual ... More Details >>
- No：23167
- Release Date：2018/09/07 16:09
Brake is not working properly.

Cause:[Occurs only when operating manually]•T/B operation error.•The enabling device input is open.[Occurs when operating manually and automatically]•Faulty ... More Details >>
- No：23183
- Release Date：2018/09/07 16:09
Operation panel does not display anything.

Cause:CPU has not started up properly.There is no power supply.An instantaneous power cut exceeding the specification level may have occurred.Measures:Check ... More Details >>
- No：23181
- Release Date：2018/09/07 16:09

1-10 of Total 18

Inquiries

page top