Cause:A noise is made as the internally mounted fan and its casing resonate. A noise is made by the fan catching interna

Cause:Deterioration in the reducer oil seal. Too much grease was applied. A grease other than the specified grease was a

Cause:Wire breakage on the hand signal line. The electronic hand controller(manufactured by TAIYO Ltd.) has failed. Faul

Cause:A servo OFF signal(SRVOFF)is being input from an external source. The operating right is not given.(IOENA paramete

Cause:The Ethernet cable is not connected surely. There are the device etc. which cause the noise and the noise has appl

Cause:An air leak/break in the piping. The solenoid bulb has failed. Wire breakage on the hand signal line. Hand signal

Cause:The fuse installed in the controller may have blown out. For the fuse blowout, there may be a ground fault or shor

Cause:The load conditions exceed the specified values(mass, inertia).The load condition settings are not suitable(HNDDAT

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Robots > Industrial/Collaborative Robots-MELFA > Vertical type robot

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ Vertical type robot ]

11-18 of Total 18

prev 2 / 2page next

An unusual noise can be heard (from RC).

Cause:A noise is made as the internally mounted fan and its casing resonate. A noise is made by the fan catching internal wiring.Measures:Check the state of ... More Details >>
- No：23168
- Release Date：2018/09/07 16:09
Oil is leaking.

Cause:Deterioration in the reducer oil seal. Too much grease was applied. A grease other than the specified grease was applied. Excess grease left on the uni... More Details >>
- No：23174
- Release Date：2018/09/07 16:09
The hand does not move properly (Electric operated hand).

Cause:Wire breakage on the hand signal line. The electronic hand controller(manufactured by TAIYO Ltd.) has failed. Faulty connection in the cables that run ... More Details >>
- No：23177
- Release Date：2018/09/07 16:09
The servo-on cannot be performed.

Cause:A servo OFF signal(SRVOFF)is being input from an external source. The operating right is not given.(IOENA parameters settings/exclusive input and outpu... More Details >>
- No：23170
- Release Date：2018/09/07 16:09
The communication fault occurs by the equipment connected to the Ethernet cable inside the robot arm.

Cause:The Ethernet cable is not connected surely. There are the device etc. which cause the noise and the noise has applied to the Ethernet cable. Measures:C... More Details >>
- No：23179
- Release Date：2018/09/07 16:09
The hand does not move properly (air hand).

Cause:An air leak/break in the piping. The solenoid bulb has failed. Wire breakage on the hand signal line. Hand signal line short circuitThe hand IF card ha... More Details >>
- No：23176
- Release Date：2018/09/07 16:09
The T/B does not display anything.

Cause:The fuse installed in the controller may have blown out. For the fuse blowout, there may be a ground fault or short circuit in the T/B cable. The T/B m... More Details >>
- No：23180
- Release Date：2018/09/07 16:09
The tip of the robot is vibrating.

Cause:The load conditions exceed the specified values(mass, inertia).The load condition settings are not suitable(HNDDAT and WRKDAT settings are not consiste... More Details >>
- No：23169
- Release Date：2018/09/07 16:09

11-18 of Total 18

Inquiries

page top