The rated impulse withstand voltage of US-H* type is 6KV. This meets therequired impulse characteristic for power distri

Since the permanent magnet is used for the electromagnet part of SD-Qtype, it is necessary to match its polarity with th

It is possible to replace it by user.

It is possible to produce with the coil designation of less than AC 230V andDC 220V. Please add " SA" at the end of the

It is the utilization category for opening/closing a heater load ofsemiconductor contactor specified in IEC60947-4-3. Ut

It has 1,000 times electrical durability using rated currents.

It is not possible to install it on the floor. If doing that, the weight of themoving part of a magnetic starter itself

It is 1500V 50/60Hz between a terminal and a case for 1 min.

Time rating is 60sec and the rest time is for 2 hours.

The minimum applicable load is 20V, 3mA . Contact reliability is indicatedby fault rate λ60 (Number of fault / Operating

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Low-voltage Power Distribution Products > Contactors and Motor Starters

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Contactors and Motor Starters

Motor Starters(142)

FAQ within [ Contactors and Motor Starters ]

41-50 of Total 142

prev 5 / 15page next

About Low-voltage Power Distribution Products

The rated impulse withstand voltage of US-H* type is 6KV. This meets therequired impulse characteristic for power distribution equipment specifiedin IEC stan... More Details >>
- No：23329
- Release Date：2018/09/12 15:11
- Category： Motor Starters
About Low-voltage Power Distribution Products

Since the permanent magnet is used for the electromagnet part of SD-Qtype, it is necessary to match its polarity with the polarity of the controlcoil. More Details >>
- No：23324
- Release Date：2018/09/12 15:11
- Category： Motor Starters
About Low-voltage Power Distribution Products

It is possible to replace it by user. More Details >>
- No：23321
- Release Date：2018/09/12 15:11
- Category： Motor Starters
About Low-voltage Power Distribution Products

It is possible to produce with the coil designation of less than AC 230V andDC 220V. Please add " SA" at the end of the type name. More Details >>
- No：23319
- Release Date：2018/09/12 15:11
- Category： Motor Starters
About Low-voltage Power Distribution Products

It is the utilization category for opening/closing a heater load ofsemiconductor contactor specified in IEC60947-4-3. Utilization categoryAC-51 applies for "... More Details >>
- No：23318
- Release Date：2018/09/12 15:11
- Category： Motor Starters
About Low-voltage Power Distribution Products

It has 1,000 times electrical durability using rated currents. More Details >>
- No：23315
- Release Date：2018/09/12 15:11
- Category： Motor Starters
About Low-voltage Power Distribution Products

It is not possible to install it on the floor. If doing that, the weight of themoving part of a magnetic starter itself acts downward against thetripping spr... More Details >>
- No：23312
- Release Date：2018/09/12 15:11
- Category： Motor Starters
About Low-voltage Power Distribution Products

It is 1500V 50/60Hz between a terminal and a case for 1 min. More Details >>
- No：23310
- Release Date：2018/09/12 15:11
- Category： Motor Starters
About Low-voltage Power Distribution Products

Time rating is 60sec and the rest time is for 2 hours. More Details >>
- No：23308
- Release Date：2018/09/12 15:11
- Category： Motor Starters
About Low-voltage Power Distribution Products

The minimum applicable load is 20V, 3mA . Contact reliability is indicatedby fault rate λ60 (Number of fault / Operating cycles per one contact) atthe reliab... More Details >>
- No：23304
- Release Date：2018/09/12 15:11
- Category： Motor Starters

41-50 of Total 142

Inquiries

page top