Since the permanent magnet is used for the electromagnet part of SD-Qtype, it is necessary to match its polarity with th

The minimum applicable load is 20V, 3mA . Contact reliability is indicatedby fault rate λ60 (Number of fault / Operating

The functions of 2 and 3 element type are almost same, but since theneutral pole (3/L2, 4/T2) of 3-pole 2-element type i

It is possible to install them by rotating 90℃ to the right or left from theregular installation except S-N600 and S-N80

It is possible to produce with the coil designation of less than AC 230V andDC 220V. Please add " SA" at the end of the

It is the utilization category for opening/closing a heater load ofsemiconductor contactor specified in IEC60947-4-3. Ut

It is not possible to install it on the floor. If doing that, the weight of themoving part of a magnetic starter itself

This is because the delay time becomes shorter since the rebound force ofa spring against the suction force of a magneti

It is possible to apply for single-phase circuit. However, it may be lesseffect in single-phase circuit (100 V, etc) sin

It is a current value that can be closed (turning contact "ON") under theconditions specified in the standards. (In IEC,

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Low-voltage Power Distribution Products > Contactors and Motor Starters

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Contactors and Motor Starters

Motor Starters(142)

FAQ within [ Contactors and Motor Starters ]

41-50 of Total 142

prev 5 / 15page next

About Low-voltage Power Distribution Products

Since the permanent magnet is used for the electromagnet part of SD-Qtype, it is necessary to match its polarity with the polarity of the controlcoil. More Details >>
- No：23324
- Release Date：2018/09/12 15:11
- Category： Motor Starters
About Low-voltage Power Distribution Products

The minimum applicable load is 20V, 3mA . Contact reliability is indicatedby fault rate λ60 (Number of fault / Operating cycles per one contact) atthe reliab... More Details >>
- No：23304
- Release Date：2018/09/12 15:11
- Category： Motor Starters
About Low-voltage Power Distribution Products

The functions of 2 and 3 element type are almost same, but since theneutral pole (3/L2, 4/T2) of 3-pole 2-element type is connected inside, itis not possible... More Details >>
- No：23270
- Release Date：2018/09/12 15:11
- Category： Motor Starters
About Low-voltage Power Distribution Products

It is possible to install them by rotating 90℃ to the right or left from theregular installation except S-N600 and S-N800. It is not possible to rotate180℃ f... More Details >>
- No：23335
- Release Date：2018/09/12 15:11
- Category： Motor Starters
About Low-voltage Power Distribution Products

It is possible to produce with the coil designation of less than AC 230V andDC 220V. Please add " SA" at the end of the type name. More Details >>
- No：23319
- Release Date：2018/09/12 15:11
- Category： Motor Starters
About Low-voltage Power Distribution Products

It is the utilization category for opening/closing a heater load ofsemiconductor contactor specified in IEC60947-4-3. Utilization categoryAC-51 applies for "... More Details >>
- No：23318
- Release Date：2018/09/12 15:11
- Category： Motor Starters
About Low-voltage Power Distribution Products

It is not possible to install it on the floor. If doing that, the weight of themoving part of a magnetic starter itself acts downward against thetripping spr... More Details >>
- No：23312
- Release Date：2018/09/12 15:11
- Category： Motor Starters
About Low-voltage Power Distribution Products

This is because the delay time becomes shorter since the rebound force ofa spring against the suction force of a magnetic contactor increases if thecontact "... More Details >>
- No：23309
- Release Date：2018/09/12 15:11
- Category： Motor Starters
About Low-voltage Power Distribution Products

It is possible to apply for single-phase circuit. However, it may be lesseffect in single-phase circuit (100 V, etc) since low voltage circuit is tendedto be... More Details >>
- No：23297
- Release Date：2018/09/12 15:11
- Category： Motor Starters
About Low-voltage Power Distribution Products

It is a current value that can be closed (turning contact "ON") under theconditions specified in the standards. (In IEC, number of tests is 50times) More Details >>
- No：23294
- Release Date：2018/09/12 15:11
- Category： Motor Starters

41-50 of Total 142

Inquiries

page top