It is the utilization category for opening/closing a heater load ofsemiconductor contactor specified in IEC60947-4-3. Ut

It is possible to produce with the coil designation of less than AC 230V andDC 220V. Please add " SA" at the end of the

By opening/closing load with SSC of the zero-voltage triggering method, itreduces noise voltage when closing.

Since the permanent magnet is used for the electromagnet part of SD-Qtype, it is necessary to match its polarity with th

You must not desassemble it since mechanical latched type has beenadjusted and tested at our factory.

You can install it as follows.1. Regular installation of the power supply side terminal as the upper partand the load si

The rated impulse withstand voltage of US-H* type is 6KV. This meets therequired impulse characteristic for power distri

There is a terminal cover for it. ( In MSOD-Q* type magnetic starter, thereis no terminal cover for the thermal load rel

It is coil capacity (power consumption) when a control coil is energizedand a contact is closed.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Low-voltage Power Distribution Products > Contactors and Motor Starters > Motor Starters

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ Motor Starters ]

61-70 of Total 142

prev 7 / 15page next

About Low-voltage Power Distribution Products

It is the utilization category for opening/closing a heater load ofsemiconductor contactor specified in IEC60947-4-3. Utilization categoryAC-51 applies for "... More Details >>
- No：23318
- Release Date：2018/09/12 15:11
About Low-voltage Power Distribution Products

It is possible to produce with the coil designation of less than AC 230V andDC 220V. Please add " SA" at the end of the type name. More Details >>
- No：23319
- Release Date：2018/09/12 15:11
About Low-voltage Power Distribution Products

By opening/closing load with SSC of the zero-voltage triggering method, itreduces noise voltage when closing. More Details >>
- No：23323
- Release Date：2018/09/12 15:11
About Low-voltage Power Distribution Products

Since the permanent magnet is used for the electromagnet part of SD-Qtype, it is necessary to match its polarity with the polarity of the controlcoil. More Details >>
- No：23324
- Release Date：2018/09/12 15:11
About Low-voltage Power Distribution Products

You must not desassemble it since mechanical latched type has beenadjusted and tested at our factory. More Details >>
- No：23325
- Release Date：2018/09/12 15:11
About Low-voltage Power Distribution Products

You can install it as follows.1. Regular installation of the power supply side terminal as the upper partand the load side terminal as the lower part2. An in... More Details >>
- No：23326
- Release Date：2018/09/12 15:11
About Low-voltage Power Distribution Products

It is IP20. More Details >>
- No：23327
- Release Date：2018/09/12 15:11
About Low-voltage Power Distribution Products

The rated impulse withstand voltage of US-H* type is 6KV. This meets therequired impulse characteristic for power distribution equipment specifiedin IEC stan... More Details >>
- No：23329
- Release Date：2018/09/12 15:11
About Low-voltage Power Distribution Products

There is a terminal cover for it. ( In MSOD-Q* type magnetic starter, thereis no terminal cover for the thermal load relay although the contactor parthas a t... More Details >>
- No：23330
- Release Date：2018/09/12 15:11
About Low-voltage Power Distribution Products

It is coil capacity (power consumption) when a control coil is energizedand a contact is closed. More Details >>
- No：23333
- Release Date：2018/09/12 15:11

61-70 of Total 142

Inquiries

page top