A reason varies with the connection situation of options. (Please refer to the section 6 of the User’s Manual.) In c

When making a transformer to energize, a large inrush current may flow. The circuit breaker is therefore required to pre

It is overcurrent tripping characteristic zone which exceeds the rated current and does not exceed short time tripping z

The applicable voltage is 440V or less. Moreover, High-speed type can be used from 85 to 484V, and Time-delay type can b

Each setting knob of the overcurrent trip characteristic is set to the maximum value and then shipped if not specified.

The fault detection contact of the cooling fan detects the temperature ofthe fin in the solid state contactor and operat

It depends on the service conditions. Refer to the following guidelines. ① Contact output Contact output for ME96 s

Please check the register addresses. The register address for the present value of the power factor of each phase is

It is voltage which ensures withstand voltage and it is used as basis to determine insulation distance.

It is the maximum voltage which meets the performance criteria for the rated operational voltage.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Low-voltage Power Distribution Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Low-voltage Power Distribution Products

Low-voltage Circuit Breakers(124)

Air Circuit Breakers(23)
Molded Case Circuit Breakers(49)
Earth Leakage Circuit Breakers(21)
Circuit Breakers for Equipment(2)
Circuit Breakers for Use in Particular Applications(6)
Accessories and Related Components(21)
Miniature Circuit Breakers(2)
Contactors and Motor Starters(142)

Motor Starters(142)

Power Management Meters(57)

Electrical Indicators(57)

FAQ within [ Low-voltage Power Distribution Products ]

191-200 of Total 322

prev 20 / 33page next

LCD COM is flashing (ME96SS series).

A reason varies with the connection situation of options. (Please refer to the section 6 of the User’s Manual.) In case of MODBUS RTU Error content: ... More Details >>
- No：22186
- Release Date：2018/08/27 16:41
- Update：2020/04/13 09:20
- Category： Electrical Indicators
Rating of a circuit breaker for transformers primary protection

When making a transformer to energize, a large inrush current may flow. The circuit breaker is therefore required to prevent unwanted trip. The selection of ... More Details >>
- No：22343
- Release Date：2018/08/31 14:33
- Category： Molded Case Circuit Breakers
LTD operating characteristic

It is overcurrent tripping characteristic zone which exceeds the rated current and does not exceed short time tripping zone (If without short time tripping ,... More Details >>
- No：22384
- Release Date：2018/08/31 14:33
- Category： Molded Case Circuit Breakers
ELCB applicable voltage

The applicable voltage is 440V or less. Moreover, High-speed type can be used from 85 to 484V, and Time-delay type can be used from 170 to 484V. More Details >>
- No：22421
- Release Date：2018/08/31 14:33
- Category： Earth Leakage Circuit Breakers
Default setting of electronic breakers

Each setting knob of the overcurrent trip characteristic is set to the maximum value and then shipped if not specified. However, only the pre-alarm is set to... More Details >>
- No：22438
- Release Date：2018/08/31 14:33
- Category： Molded Case Circuit Breakers
About Low-voltage Power Distribution Products

The fault detection contact of the cooling fan detects the temperature ofthe fin in the solid state contactor and operates when exceeding thespecified value.... More Details >>
- No：23301
- Release Date：2018/09/12 15:11
- Category： Motor Starters
Wire length for analog output and contact output（ME96SS series）

It depends on the service conditions. Refer to the following guidelines. ① Contact output Contact output for ME96 series is no-voltage "a" contact. The... More Details >>
- No：24807
- Release Date：2019/03/27 12:12
- Category： Electrical Indicators
The power factor does not match the indication values through MODBUS.

Please check the register addresses. The register address for the present value of the power factor of each phase is “0789”. There are the register... More Details >>
- No：37807
- Release Date：2020/04/10 15:10
- Category： Electrical Indicators
Rated insulation voltage

It is voltage which ensures withstand voltage and it is used as basis to determine insulation distance. More Details >>
- No：22362
- Release Date：2018/08/31 14:33
- Category： Molded Case Circuit Breakers
Operational voltage

It is the maximum voltage which meets the performance criteria for the rated operational voltage. More Details >>
- No：22367
- Release Date：2018/08/31 14:33
- Category： Molded Case Circuit Breakers

191-200 of Total 322

Inquiries

page top