Pressing the buttons of the “Set” for 2 seconds or more shifts the mode to the “Setting Value Confirmation Mode”. It i

AX (Auxiliary switch) is a switch which electrically displays the ON / OFF state. The markings are 14/AXa, 12/AXb and 11

The minimum applicable load is as follows. Contact reliability is indicatedby fault rate λ60 (Number of fault / Operatin

When [SET] is flashing, the “Setting Value Confirmation Mode” is selected. In this case, the set values cannot be change

When the AC waveform distorted due to harmonics, the value changes. (For AC without harmonics, the calculated value will

The circuit breaker is designed to attain a predetermined value of limiting non-actuating time corresponding to a given

Since the total electric circuit length of upstream circuit breaker side is longer than that of downstream circuit break

It is no influence on operating and characteristics even in the following cases. 1. Overcurrent 20 times of rated curr

The range of ambient temperature is from -10 to 40 degree Celsius for not only MCCB but also including Earth Leakage Cir

It may not trip a fault current or degrade insulation after tripping. When you connect the device in reverse, you must s

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Low-voltage Power Distribution Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Low-voltage Power Distribution Products

Low-voltage Circuit Breakers(124)

Air Circuit Breakers(23)
Molded Case Circuit Breakers(49)
Earth Leakage Circuit Breakers(21)
Circuit Breakers for Equipment(2)
Circuit Breakers for Use in Particular Applications(6)
Accessories and Related Components(21)
Miniature Circuit Breakers(2)
Contactors and Motor Starters(142)

Motor Starters(142)

Power Management Meters(57)

Electrical Indicators(57)

FAQ within [ Low-voltage Power Distribution Products ]

271-280 of Total 322

prev 28 / 33page next

Checking the set values (ME96SS series).

Pressing the buttons of the “Set” for 2 seconds or more shifts the mode to the “Setting Value Confirmation Mode”. It is impossible to change the set values... More Details >>
- No：22165
- Release Date：2018/08/27 16:41
- Category： Electrical Indicators
AX

AX (Auxiliary switch) is a switch which electrically displays the ON / OFF state. The markings are 14/AXa, 12/AXb and 11/AXc.* If the circuit breaker itself ... More Details >>
- No：22354
- Release Date：2018/08/31 14:33
- Category： Accessories and Related Components
About Low-voltage Power Distribution Products

The minimum applicable load is as follows. Contact reliability is indicatedby fault rate λ60 (Number of fault / Operating cycles per one contact) atthe relia... More Details >>
- No：23320
- Release Date：2018/09/12 15:11
- Category： Motor Starters
Set values cannot be changed on the setting mode (ME96SS series).

When[SET] is flashing, the “Setting Value Confirmation Mode” is selected. In this case, the set values cannot be changed. Pressing the buttons of the “Set” ... More Details >>
- No：22168
- Release Date：2018/08/27 16:41
- Update：2020/04/10 16:22
- Category： Electrical Indicators
Difference between measurement value of active power and calculated power value obtained from current, voltage and power factor (ME96SS series).

When the AC waveform distorted due to harmonics, the value changes. (For AC without harmonics, the calculated value will match with the displayed value.) A... More Details >>
- No：22178
- Release Date：2018/08/27 16:41
- Update：2020/04/10 16:56
- Category： Electrical Indicators
Time-delay CBR

The circuit breaker is designed to attain a predetermined value of limiting non-actuating time corresponding to a given value of residual current. Our time-d... More Details >>
- No：22351
- Release Date：2018/08/31 14:33
- Category： Earth Leakage Circuit Breakers
Earth leakage protective coordination

Since the total electric circuit length of upstream circuit breaker side is longer than that of downstream circuit breaker, constant earth leakage current b... More Details >>
- No：22369
- Release Date：2018/08/31 14:33
- Category： Earth Leakage Circuit Breakers
Tolerance for overload (ME96SS series).

It is no influence on operating and characteristics even in the following cases. 1. Overcurrent 20 times of rated current is applied for 0.5 second. 2. Ov... More Details >>
- No：22159
- Release Date：2018/08/27 16:41
- Category： Electrical Indicators
Ambient temperature

The range of ambient temperature is from -10 to 40 degree Celsius for not only MCCB but also including Earth Leakage Circuit breaker, Earth Leakage Relay and... More Details >>
- No：22352
- Release Date：2018/08/31 14:33
- Category： Molded Case Circuit Breakers
Wrong connection in reverse

It may not trip a fault current or degrade insulation after tripping. When you connect the device in reverse, you must select a reverse-connectable model. More Details >>
- No：22345
- Release Date：2018/08/31 14:33
- Category： Molded Case Circuit Breakers

271-280 of Total 322

Inquiries

page top