When the AC waveform distorted due to harmonics, the value changes. (For AC without harmonics, the calculated value will

In general, in case of measurement by the average method, the waveform including harmonics cause large error. This model

When [SET] is flashing, the “Setting Value Confirmation Mode” is selected. In this case, the set values cannot be change

It is the utilization category for opening/closing a motor load ofsemiconductor contactor specified in IEC60947-4-2. Uti

This contact(SBC) is used to auxiliary switch(AXb) contact. When Drawout type ACB is moved from "test" position to "disc

At time-delay tripping zone, it operates with bimetal, therefore the characteristics of AC and DC should be same if the

Both of the adjustment knob is set to the maximum value when shipping in order to prevent unwanted earth leakage trippin

1) For the main body of ME96: Please set the following values on the “Set-up menu 2”. In case of MODBUS RTU S

It is necessary to supply an auxiliary power. As for an auxiliary power supply, you can use 50 Hz or 60 Hz from 100 VAC

AE-SW 4-poles with WS relay (general protection) has overcurrent protection for neutral-pole. The tripping characterist

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Low-voltage Power Distribution Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Low-voltage Power Distribution Products

Low-voltage Circuit Breakers(124)

Air Circuit Breakers(23)
Molded Case Circuit Breakers(49)
Earth Leakage Circuit Breakers(21)
Circuit Breakers for Equipment(2)
Circuit Breakers for Use in Particular Applications(6)
Accessories and Related Components(21)
Miniature Circuit Breakers(2)
Contactors and Motor Starters(142)

Motor Starters(142)

Power Management Meters(57)

Electrical Indicators(57)

FAQ within [ Low-voltage Power Distribution Products ]

61-70 of Total 322

prev 7 / 33page next

Difference between measurement value of active power and calculated power value obtained from current, voltage and power factor (ME96SS series).

When the AC waveform distorted due to harmonics, the value changes. (For AC without harmonics, the calculated value will match with the displayed value.) A... More Details >>
- No：22178
- Release Date：2018/08/27 16:41
- Update：2020/04/10 16:56
- Category： Electrical Indicators
Measurement value different from other measuring instrument (ME96SS series).

In general, in case of measurement by the average method, the waveform including harmonics cause large error. This model uses the RMS value method and measu... More Details >>
- No：22177
- Release Date：2018/08/27 16:41
- Update：2020/04/10 16:54
- Category： Electrical Indicators
Set values cannot be changed on the setting mode (ME96SS series).

When[SET] is flashing, the “Setting Value Confirmation Mode” is selected. In this case, the set values cannot be changed. Pressing the buttons of the “Set” ... More Details >>
- No：22168
- Release Date：2018/08/27 16:41
- Update：2020/04/10 16:22
- Category： Electrical Indicators
About Low-voltage Power Distribution Products

It is the utilization category for opening/closing a motor load ofsemiconductor contactor specified in IEC60947-4-2. Utilization categoryAC-53a applies for "... More Details >>
- No：23345
- Release Date：2018/09/12 15:12
- Category： Motor Starters
ACB　Shorting B contact (SBC)

This contact(SBC) is used to auxiliary switch(AXb) contact. When Drawout type ACB is moved from "test" position to "disconnect" position, AXb contact will b... More Details >>
- No：22416
- Release Date：2018/08/31 14:33
- Category： Air Circuit Breakers
Inst tripping current value of AC/DC common breaker

At time-delay tripping zone, it operates with bimetal, therefore the characteristics of AC and DC should be same if the effective values of them are same. Ho... More Details >>
- No：22392
- Release Date：2018/08/31 14:33
- Category： Molded Case Circuit Breakers
ELCB Default setting Time-delay type sensitivity

Both of the adjustment knob is set to the maximum value when shipping in order to prevent unwanted earth leakage tripping when Earth Leakage Circuit Breaker ... More Details >>
- No：22388
- Release Date：2018/08/31 14:33
- Category： Earth Leakage Circuit Breakers
Setting for communication (ME96SS series).

1) For the main body of ME96: Please set the following values on the “Set-up menu 2”. In case of MODBUS RTU 　 Set-up menu No. Setti... More Details >>
- No：22181
- Release Date：2018/08/27 16:41
- Update：2020/04/10 17:05
- Category： Electrical Indicators
Power supply upon setting (ME96SS series).

It is necessary to supply an auxiliary power. As for an auxiliary power supply, you can use 50 Hz or 60 Hz from 100 VAC to 240 VAC and from 100 VDC to 240... More Details >>
- No：22161
- Release Date：2018/08/27 16:41
- Update：2020/04/10 16:14
- Category： Electrical Indicators
Release element in neutral (4P breaker)

AE-SW 4-poles with WS relay (general protection) has overcurrent protection for neutral-pole. The tripping characteristic is same as phase-pole. Moreover, A... More Details >>
- No：22441
- Release Date：2018/08/31 14:33
- Category： Air Circuit Breakers

61-70 of Total 322

Inquiries

page top