The measurement elements, including the digital indication, the unit indication and the phase indication, flash. And t

Pressing buttons of the “+” and the “-” at the same time on the measurement screen for 2 seconds shifts the unit of ac

ME96SSHB-MB • Total harmonics and odd orders of harmonics from 1st to 31st • Effective value and distorti

This model has “Motor Starting Current Mask Function”. This function stops the alarm output and updating of the maximum

In general, in case of measurement by the average method, the waveform including harmonics cause large error. This mode

Please check the following items. (A) Is the power supplied between MA and MB？ (When the power is not supplied, the di

The acquired value by communication should be multiplied by the multiplying factor to change into the measurement va

The acquired digit length of “1280”, “1281” and “1304” varies with the full load power. The acquired digit length of

Please check the register addresses. The register address for the present value of the power factor of each phase is “

It depends on the service conditions. Refer to the following guidelines. ① Contact output Contact output for ME9

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Low-voltage Power Distribution Products > Power Management Meters > Electrical Indicators

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ Electrical Indicators ]

31-40 of Total 57

prev 4 / 6page next

Display upon upper/lower limit alarm (ME96SS series).

The measurement elements, including the digital indication, the unit indication and the phase indication, flash. And the “ALARM” indication and the “HI” in... More Details >>
- No：22169
- Release Date：2018/08/27 16:41
- Update：2020/04/10 16:36
Checking non-displayed digit of active energy (ME96SS series).

Pressing buttons of the “+” and the “-” at the same time on the measurement screen for 2 seconds shifts the unit of active energy as follows. The measured ... More Details >>
- No：22172
- Release Date：2018/08/27 16:41
- Update：2020/04/10 16:44
Measuring harmonics range (ME96SS series).

ME96SSHB-MB • Total harmonics and odd orders of harmonics from 1st to 31st •Effective value and distortion rate. • Harmonic current and Harmonic... More Details >>
- No：22173
- Release Date：2018/08/27 16:41
- Update：2020/04/10 16:46
Disable an alarm for motor starting current (ME96SS series).

This model has “Motor Starting Current Mask Function”. This function stops the alarm output and updating of the maximum values during the setting time when a... More Details >>
- No：22175
- Release Date：2018/08/27 16:41
- Update：2020/04/10 16:51
Measurement value different from other measuring instrument (ME96SS series).

In general, in case of measurement by the average method, the waveform including harmonics cause large error. This model uses the RMS value method and measu... More Details >>
- No：22177
- Release Date：2018/08/27 16:41
- Update：2020/04/10 16:54
Communication failure with the upper system through MODBUS RTU.

Please check the following items. (A) Is the power supplied between MA and MB？ (When the power is not supplied, the display does not work.) (B) Is the wir... More Details >>
- No：22182
- Release Date：2018/08/27 16:41
- Update：2020/04/10 17:08
Acquired values through MODBUS RTU.

The acquired value by communication should be multiplied by the multiplying factor to change into the measurement value. Please refer to Section 7.3 of ... More Details >>
- No：22183
- Release Date：2018/08/27 16:41
- Update：2020/04/13 09:13
Register address for active energy monitors in the MODBUS RTU communication (ME96SS series).

The acquired digit length of “1280”, “1281” and “1304” varies with the full load power. The acquired digit length of “1304” is 6-digit. Each of “1280” and... More Details >>
- No：22184
- Release Date：2018/08/27 16:41
- Update：2020/04/10 17:18
Indication values of the main body is different from an obtained value through MODBUS RTU/ TCP (ME96SS series).

Please check the register addresses. The register address for the present value of the power factor of each phase is “0789”. There are the register addre... More Details >>
- No：22191
- Release Date：2018/08/27 16:41
Wire length for analog output and contact output（ME96SS series）

It depends on the service conditions. Refer to the following guidelines. ① Contact output Contact output for ME96 series is no-voltage "a" contact. The... More Details >>
- No：24807
- Release Date：2019/03/27 12:12

31-40 of Total 57

Inquiries

page top