It operates on a root mean square value of a fundamental wave.

It is required that the resistance is lower than 5 ohm for a go and return length using sealed cables. The high voltage

Input from the primary side by combining with a peripheral device (ZCT). In Standard JIS C 4601, performance warranty is

Set the display selection switch on the front upper right of the relay to “Time limit pass.” When a relay detects near t

Overload tolerance of an over current relay is 200 A, 1 second. Adjust CT ratio and others not to input more than 200 A.

It means multiples of the settling value. For example, when an instantaneous factor operation settling value of a relay

It is impossible. Because the type is to detect by ZCT in an ungrounded system, the sensitivity becomes very high.

It is required that the resistance is lower than 5 ohm for a go and return length using sealed cables. Other than MPD-3

That is right. Standard JIS C 4602 defines it shall be 50ms or shorter when 200% of the settling value is input.

Because the contact capacity is different to that of a contact for trip, it cannot be used for tripping. Refer to the ca

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Medium-voltage Power Distribution Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Medium-voltage Power Distribution Products

Protection Relays(72)

Protection Relays - MELPRO-A Series(72)

FAQ within [ Medium-voltage Power Distribution Products ]

11-20 of Total 36

prev 2 / 4page next

Detection of current

It operates on a root mean square value of a fundamental wave. More Details >>
- No：23710
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC
Combination transformer

It is required that the resistance is lower than 5 ohm for a go and return length using sealed cables. The high voltage receiving facility rule defines “The ... More Details >>
- No：23730
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MGR
Test method

Input from the primary side by combining with a peripheral device (ZCT). In Standard JIS C 4601, performance warranty is covered for combination of periphera... More Details >>
- No：23728
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MGR
Confirmation method of the start-up value

Set the display selection switch on the front upper right of the relay to “Time limit pass.” When a relay detects near the operation value, “0” will be displ... More Details >>
- No：23716
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC
Short-circuit detection

Overload tolerance of an over current relay is 200 A, 1 second. Adjust CT ratio and others not to input more than 200 A. More Details >>
- No：23711
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC
The viewpoint of the instantaneous factor operating characteristics graph

It means multiples of the settling value. For example, when an instantaneous factor operation settling value of a relay is 30 A, 100% is read as 30 A. More Details >>
- No：23707
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC
Scope of Application

It is impossible. Because the type is to detect by ZCT in an ungrounded system, the sensitivity becomes very high. More Details >>
- No：23727
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MGR
Combination transformer

It is required that the resistance is lower than 5 ohm for a go and return length using sealed cables. Other than MPD-3 type ZVT, it is similar to the distan... More Details >>
- No：23719
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MDG
The operating time of the instantaneous factor operating characteristics

That is right. Standard JIS C 4602 defines it shall be 50ms or shorter when 200% of the settling value is input. More Details >>
- No：23706
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC
About contact

Because the contact capacity is different to that of a contact for trip, it cannot be used for tripping. Refer to the catalog for the contact capacity. More Details >>
- No：23737
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , COMMON

11-20 of Total 36

Inquiries

page top