It is required that the resistance is lower than 5 ohm for a go and return length using sealed cables. The high voltage

Set the display selection switch on the front upper right of the relay to “Time limit pass.” When a relay detects near t

It means multiples of the settling value. For example, when an instantaneous factor operation settling value of a relay

It is impossible. In Standard JIS C 4609, warranty is covered for combination of peripheral devices and relays. Therefor

It is possible. Connect R-phase to the terminal for R-phase of the relay, and T-phase to the terminal for T-phase of the

That is right. Standard JIS C 4602 defines it shall be 50ms or shorter when 200% of the settling value is input.

It means multiples of the settling value. For example, when a definite time factor operation settling value of a relay i

That is described as below. (1) By laying ZCTs for two feeders having different loads, detected by one earth fault dir

Because the contact capacity is different to that of a contact for trip, it cannot be used for tripping. Refer to the ca

A momentary power interruption is not detectable.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Medium-voltage Power Distribution Products > Protection Relays

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Protection Relays

Protection Relays - MELPRO-A Series(72)

MOC(13)
MGR(5)
MDG(8)
MUV(6)
COMMON(4)

FAQ within [ Protection Relays ]

11-20 of Total 36

prev 2 / 4page next

Combination transformer

It is required that the resistance is lower than 5 ohm for a go and return length using sealed cables. The high voltage receiving facility rule defines “The ... More Details >>
- No：23730
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MGR
Confirmation method of the start-up value

Set the display selection switch on the front upper right of the relay to “Time limit pass.” When a relay detects near the operation value, “0” will be displ... More Details >>
- No：23716
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC
The viewpoint of the instantaneous factor operating characteristics graph

It means multiples of the settling value. For example, when an instantaneous factor operation settling value of a relay is 30 A, 100% is read as 30 A. More Details >>
- No：23707
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC
Combination with other companies' peripheral devices

It is impossible. In Standard JIS C 4609, warranty is covered for combination of peripheral devices and relays. Therefore, combination with other companies’ ... More Details >>
- No：23718
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MDG
The application of the overcurrent relay

It is possible. Connect R-phase to the terminal for R-phase of the relay, and T-phase to the terminal for T-phase of the relay. And the direction of a curren... More Details >>
- No：23709
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC
The operating time of the instantaneous factor operating characteristics

That is right. Standard JIS C 4602 defines it shall be 50ms or shorter when 200% of the settling value is input. More Details >>
- No：23706
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC
The viewpoint of the definite time factor characteristic graph

It means multiples of the settling value. For example, when a definite time factor operation settling value of a relay is 3 A, 1x is read as 3 A and 5x is re... More Details >>
- No：23705
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC
Combination transformer

That is described as below. (1) By laying ZCTs for two feeders having different loads, detected by one earth fault directional relay. In this case, it i... More Details >>
- No：23726
- Release Date：2018/09/19 17:16
- Update：2018/09/20 13:26
- Category： Protection Relays - MELPRO-A Series , MGR
About contact

Because the contact capacity is different to that of a contact for trip, it cannot be used for tripping. Refer to the catalog for the contact capacity. More Details >>
- No：23737
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , COMMON
Detection of undervoltage

A momentary power interruption is not detectable. More Details >>
- No：23732
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MUV

11-20 of Total 36

Inquiries

page top