It is impossible. In Standard JIS C 4609, warranty is covered for combination of peripheral devices and relays. Therefor

It lights up with 85 V or more control power.

In steady state, it is 5.0 VA, and during operation, it is 6.0 VA.

It is possible. Connect R-phase to the terminal for R-phase of the relay, and T-phase to the terminal for T-phase of the

That is described as below. (1) By laying ZCTs for two feeders having different loads, detected by one earth fault dir

Overload tolerance of an over current relay is 200 A, 1 second. Adjust CT ratio and others not to input more than 200 A.

It operates on a root mean square value of a fundamental wave.

Set the display selection switch on the front upper right of the relay to “Time limit pass.” When a relay detects near t

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Medium-voltage Power Distribution Products > Protection Relays > Protection Relays - MELPRO-A Series

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Protection Relays - MELPRO-A Series

COMMON(4)

FAQ within [ Protection Relays - MELPRO-A Series ]

11-20 of Total 36

prev 2 / 4page next

About contact

That is right. More Details >>
- No：23722
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MDG
Combination with other companies' peripheral devices

It is impossible. In Standard JIS C 4609, warranty is covered for combination of peripheral devices and relays. Therefore, combination with other companies’ ... More Details >>
- No：23718
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MDG
Direction of the current in the incident detection

It is possible. More Details >>
- No：23712
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC
A lighting condition of the RUN LED

It lights up with 85 V or more control power. More Details >>
- No：23721
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MDG
Burden of MOC-A1 type

In steady state, it is 5.0 VA, and during operation, it is 6.0 VA. More Details >>
- No：23715
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC
The application of the overcurrent relay

It is possible. Connect R-phase to the terminal for R-phase of the relay, and T-phase to the terminal for T-phase of the relay. And the direction of a curren... More Details >>
- No：23709
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC
Combination transformer

That is described as below. (1) By laying ZCTs for two feeders having different loads, detected by one earth fault directional relay. In this case, it i... More Details >>
- No：23726
- Release Date：2018/09/19 17:16
- Update：2018/09/20 13:26
- Category： Protection Relays - MELPRO-A Series , MGR
Short-circuit detection

Overload tolerance of an over current relay is 200 A, 1 second. Adjust CT ratio and others not to input more than 200 A. More Details >>
- No：23711
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC
Detection of current

It operates on a root mean square value of a fundamental wave. More Details >>
- No：23710
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC
Confirmation method of the start-up value

Set the display selection switch on the front upper right of the relay to “Time limit pass.” When a relay detects near the operation value, “0” will be displ... More Details >>
- No：23716
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC

11-20 of Total 36

Inquiries

page top