This relay has a capacitor to operate in case of the lost power or at the maximum settling of an operation time. Because

It operates on a root mean square value of a fundamental wave.

That is described as below. (1) By laying ZCTs for two feeders having different loads, detected by one earth fault dir

Overload tolerance of an over current relay is 200 A, 1 second. Adjust CT ratio and others not to input more than 200 A.

Set the display selection switch on the front upper right of the relay to “Time limit pass.” When a relay detects near t

In steady state, it is 5.0 VA, and during operation, it is 6.0 VA.

It is possible. Connect R-phase to the terminal for R-phase of the relay, and T-phase to the terminal for T-phase of the

Input from the primary side by combining with a peripheral device (ZCT). In Standard JIS C 4601, performance warranty is

It means multiples of the settling value. For example, when an instantaneous factor operation settling value of a relay

Because the contact capacity is different to that of a contact for trip, it cannot be used for tripping. Refer to the ca

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Medium-voltage Power Distribution Products > Protection Relays > Protection Relays - MELPRO-A Series

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Protection Relays - MELPRO-A Series

COMMON(4)

FAQ within [ Protection Relays - MELPRO-A Series ]

11-20 of Total 36

prev 2 / 4page next

Contact recovery delay after applying voltage

This relay has a capacitor to operate in case of the lost power or at the maximum settling of an operation time. Because this capacitor needs a time to be ch... More Details >>
- No：23734
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MUV
Detection of current

It operates on a root mean square value of a fundamental wave. More Details >>
- No：23710
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC
Combination transformer

That is described as below. (1) By laying ZCTs for two feeders having different loads, detected by one earth fault directional relay. In this case, it i... More Details >>
- No：23726
- Release Date：2018/09/19 17:16
- Update：2018/09/20 13:26
- Category： Protection Relays - MELPRO-A Series , MGR
Short-circuit detection

Overload tolerance of an over current relay is 200 A, 1 second. Adjust CT ratio and others not to input more than 200 A. More Details >>
- No：23711
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC
Confirmation method of the start-up value

Set the display selection switch on the front upper right of the relay to “Time limit pass.” When a relay detects near the operation value, “0” will be displ... More Details >>
- No：23716
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC
Burden of MOC-A1 type

In steady state, it is 5.0 VA, and during operation, it is 6.0 VA. More Details >>
- No：23715
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC
The application of the overcurrent relay

It is possible. Connect R-phase to the terminal for R-phase of the relay, and T-phase to the terminal for T-phase of the relay. And the direction of a curren... More Details >>
- No：23709
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC
Test method

Input from the primary side by combining with a peripheral device (ZCT). In Standard JIS C 4601, performance warranty is covered for combination of periphera... More Details >>
- No：23728
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MGR
The viewpoint of the instantaneous factor operating characteristics graph

It means multiples of the settling value. For example, when an instantaneous factor operation settling value of a relay is 30 A, 100% is read as 30 A. More Details >>
- No：23707
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC
About contact

Because the contact capacity is different to that of a contact for trip, it cannot be used for tripping. Refer to the catalog for the contact capacity. More Details >>
- No：23737
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , COMMON

11-20 of Total 36

Inquiries

page top