It is required that the resistance is lower than 5 ohm for a go and return length using sealed cables. Other than MPD-3

Set the display selection switch on the front upper right of the relay to “Time limit pass.” When a relay detects near t

Overload tolerance of an over current relay is 200 A, 1 second. Adjust CT ratio and others not to input more than 200 A.

Input from the primary side by combining with a peripheral device (ZCT). In Standard JIS C 4601, performance warranty is

It is required that the resistance is lower than 5 ohm for a go and return length using sealed cables. The high voltage

It operates on a root mean square value of a fundamental wave.

The prohibition position sets the maximum settling value. With the definite time current, all prohibition positions set

It lights up with 85 V or more control power.

That is described as below. (1) By laying ZCTs for two feeders having different loads, detected by one earth fault dir

It is possible. Connect R-phase to the terminal for R-phase of the relay, and T-phase to the terminal for T-phase of the

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Medium-voltage Power Distribution Products > Protection Relays > Protection Relays - MELPRO-A Series

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Protection Relays - MELPRO-A Series

COMMON(4)

FAQ within [ Protection Relays - MELPRO-A Series ]

21-30 of Total 36

prev 3 / 4page next

Combination transformer

It is required that the resistance is lower than 5 ohm for a go and return length using sealed cables. Other than MPD-3 type ZVT, it is similar to the distan... More Details >>
- No：23719
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MDG
Confirmation method of the start-up value

Set the display selection switch on the front upper right of the relay to “Time limit pass.” When a relay detects near the operation value, “0” will be displ... More Details >>
- No：23716
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC
Short-circuit detection

Overload tolerance of an over current relay is 200 A, 1 second. Adjust CT ratio and others not to input more than 200 A. More Details >>
- No：23711
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC
Test method

Input from the primary side by combining with a peripheral device (ZCT). In Standard JIS C 4601, performance warranty is covered for combination of periphera... More Details >>
- No：23728
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MGR
Combination transformer

It is required that the resistance is lower than 5 ohm for a go and return length using sealed cables. The high voltage receiving facility rule defines “The ... More Details >>
- No：23730
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MGR
Detection of current

It operates on a root mean square value of a fundamental wave. More Details >>
- No：23710
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC
Position of switch

The prohibition position sets the maximum settling value. With the definite time current, all prohibition positions set 6 A, and with the instantaneous curre... More Details >>
- No：23714
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC
A lighting condition of the RUN LED

It lights up with 85 V or more control power. More Details >>
- No：23721
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MDG
Combination transformer

That is described as below. (1) By laying ZCTs for two feeders having different loads, detected by one earth fault directional relay. In this case, it i... More Details >>
- No：23726
- Release Date：2018/09/19 17:16
- Update：2018/09/20 13:26
- Category： Protection Relays - MELPRO-A Series , MGR
The application of the overcurrent relay

It is possible. Connect R-phase to the terminal for R-phase of the relay, and T-phase to the terminal for T-phase of the relay. And the direction of a curren... More Details >>
- No：23709
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC

21-30 of Total 36

Inquiries

page top