Set the display selection switch on the front upper right of the relay to “Time limit pass.” When a relay detects near t

It is impossible. Because the type is to detect by ZCT in an ungrounded system, the sensitivity becomes very high.

It is required that the resistance is lower than 5 ohm for a go and return length using sealed cables. Other than MPD-3

It lights up with 85 V or more control power.

The prohibition position sets the maximum settling value. With the definite time current, all prohibition positions set

That is right. Standard JIS C 4602 defines it shall be 50ms or shorter when 200% of the settling value is input.

Up to 5 units. To connect 6 or more units, use Vo extended terminals (M-N) of a relay connected from MPD-3 type. From th

Because the contact capacity is different to that of a contact for trip, it cannot be used for tripping. Refer to the ca

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Medium-voltage Power Distribution Products > Protection Relays > Protection Relays - MELPRO-A Series

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Protection Relays - MELPRO-A Series

COMMON(4)

FAQ within [ Protection Relays - MELPRO-A Series ]

1-10 of Total 36

prev 1 / 4page next

Confirmation method of the start-up value

Set the display selection switch on the front upper right of the relay to “Time limit pass.” When a relay detects near the operation value, “0” will be displ... More Details >>
- No：23716
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC
Scope of Application

It is impossible. Because the type is to detect by ZCT in an ungrounded system, the sensitivity becomes very high. More Details >>
- No：23727
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MGR
Combination transformer

It is required that the resistance is lower than 5 ohm for a go and return length using sealed cables. Other than MPD-3 type ZVT, it is similar to the distan... More Details >>
- No：23719
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MDG
A lighting condition of the RUN LED

It lights up with 85 V or more control power. More Details >>
- No：23721
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MDG
Position of switch

The prohibition position sets the maximum settling value. With the definite time current, all prohibition positions set 6 A, and with the instantaneous curre... More Details >>
- No：23714
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC
The operating time of the instantaneous factor operating characteristics

That is right. Standard JIS C 4602 defines it shall be 50ms or shorter when 200% of the settling value is input. More Details >>
- No：23706
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC
Combination transformer

Up to 5 units. To connect 6 or more units, use Vo extended terminals (M-N) of a relay connected from MPD-3 type. From this Vo extended terminals, additional ... More Details >>
- No：23725
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MDG
About contact

Because the contact capacity is different to that of a contact for trip, it cannot be used for tripping. Refer to the catalog for the contact capacity. More Details >>
- No：23737
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , COMMON
Movement indicator

It operates. More Details >>
- No：23739
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , COMMON
Rated current

In CT circuit, it is 5 A. More Details >>
- No：23713
- Release Date：2018/09/19 17:16
- Category： Protection Relays - MELPRO-A Series , MOC

1-10 of Total 36

Inquiries

page top