“off” is shown in th

Operation mode for manufacturer setting is enabled. For MR-J4-B, MR-J4W2-B and MR-J4W3-B, turning "ON (up)" all the cont

When the rotary switch is “0”, the 1st axis and is “1”, the 2nd axis. When the rotary switch is “A”, the 11th axis and i

You can solder the wiring to the connector without using the junction terminal block (option).

For the safety of use, the wiring is recommended. If not using the wiring, set the parameter No. PA04 to “0100”.

In case that only main circuit power supply is cut off, communication remains. In case that the control circuit power su

Use the option cable, “MR-J3CN6CBL1M” for the analog monitor of MR-J4-A.

The system is probably malfunctioning and is in dangerous condition. Do not use it. For repair, contact your local sales

By either of following methods: (MR-J4) 1. On MR Configurator2, select [Diagnosis] - [Alarm Display] - [Clear]. 2. Set

Depending on each cable. Refer to each SSCNET III/H compatible servo amplifier instruction manual.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > AC Servos-MELSERVO > MELSERVO-J4

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ MELSERVO-J4 ]

1-10 of Total 29

prev 1 / 3page next

“off” is shown in the display.

Operation mode for manufacturer setting is enabled. For MR-J4-B, MR-J4W2-B and MR-J4W3-B, turning "ON (up)" all the control axis setting switches (SW2) enabl... More Details >>
- No：23625
- Release Date：2018/09/14 15:10
Relationship between rotary switch and axis number

When the rotary switch is “0”, the 1st axis and is “1”, the 2nd axis. When the rotary switch is “A”, the 11th axis and is “F”, the 16th axis. In combination ... More Details >>
- No：23644
- Release Date：2018/09/14 15:10
Wiring to connector

You can solder the wiring to the connector without using the junction terminal block (option). More Details >>
- No：23654
- Release Date：2018/09/14 15:10
Is the forced stop signal wiring necessary?

For the safety of use, the wiring is recommended. If not using the wiring, set the parameter No. PA04 to “0100”. More Details >>
- No：23645
- Release Date：2018/09/14 15:10
SSCNET III/H during the power supply shut-off

In case that only main circuit power supply is cut off, communication remains. In case that the control circuit power supply of servo amplifier is cut off, t... More Details >>
- No：23646
- Release Date：2018/09/14 15:10
Monitor cable

Use the option cable, “MR-J3CN6CBL1M” for the analog monitor of MR-J4-A. More Details >>
- No：23655
- Release Date：2018/09/14 15:10
Replacement of MR-BAT6V1SET

No More Details >>
- No：23649
- Release Date：2018/09/14 15:10
Wrong connection of servo amplifier power supply

The system is probably malfunctioning and is in dangerous condition. Do not use it. For repair, contact your local sales office. More Details >>
- No：23623
- Release Date：2018/09/14 15:10
Clearing the alarm history

By either of following methods: (MR-J4) 1. On MR Configurator2, select [Diagnosis] - [Alarm Display] - [Clear]. 2. Set alarm history clear of parameter to "... More Details >>
- No：23650
- Release Date：2018/09/14 15:10
SSCNET III cable type

Depending on each cable. Refer to each SSCNET III/H compatible servo amplifier instruction manual. More Details >>
- No：23652
- Release Date：2018/09/14 15:10

1-10 of Total 29

Inquiries

page top