As shown in the figure below, a current transformer (CT) with a secondary current of 5A is attached to the measurement l

There is no way to detect a disconnection or communications error in the Energy measuring Unit. As an alternative idea,

A dedicated Display Unit (Model: EMU4-D65) is used to set the EcoMonitorPlus (Model ：EMU4-BM1-MB, EMU4-HM1-MB, EMU4-LG1

(1) Open the front cover on the server section, and set the MODE switch to the "STOP" position. (2) Set the RESET switch

EMU4-LM outputs data file at following timing. 1. When inserting the SD memory card while operating. 2. When power

Use an extension cable (Model: EMU2-CB-T1M / EMU2-CB-T5M/EMU2-CB-T10M / EMU2-CB-T1MS / EMU2-CB-T5MS / EMU2-CB-T10MS) for

MEASURE LED lights while measuring electric power over 0.4% of the total load power. Check below points: 1. Is voltage

The timing for ejecting an SD memory card is specified as below table according to the state of the [SD C.] LED of the L

It will stop outputting logging data from the Logging Unit. [SD C.] LED will be high-speed blinking （repeat of 0.25sec

For 3P4W circuits, set the VT primary voltage value (between L and N). Except for 3P4W circuits, set the VT primary volt

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Energy Saving Supporting Devices > Energy Saving Supporting Devices

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Energy Saving Supporting Devices

FAQ within [ Energy Saving Supporting Devices ]

31-40 of Total 47

prev 4 / 5page next

How to measure circuits over 600A (EcoMonitorPlus / Light)

As shown in the figure below, a current transformer (CT) with a secondary current of 5A is attached to the measurement location, and a split-type current sen... More Details >>
- No：38042
- Release Date：2021/02/25 17:54
- Category： Energy Measuring Units
Checking the disconnection or communications error status of the Energy measuring Unit

There is no way to detect a disconnection or communications error in the Energy measuring Unit. As an alternative idea, we have two solutions to monitor t... More Details >>
- No：38043
- Release Date：2021/02/25 17:54
- Category： Energy Saving Data Collecting Servers
As to settings for EcoMonitorPlus (Model: EMU4-BM1-MB, EMU4-HM1-MB, EMU4-LG1-MB, EMU4-A2, EMU4-VA2, EMU4-AX4, EMU4-PX4).

A dedicated Display Unit (Model: EMU4-D65) is used to set the EcoMonitorPlus (Model ：EMU4-BM1-MB, EMU4-HM1-MB, EMU4-LG1-MB, EMU4-A2, EMU4-VA2, EMU4-AX4, EMU... More Details >>
- No：22128
- Release Date：2018/08/27 16:41
- Category： Energy Measuring Units
Checking the IP address of EcoWebServerIII

(1) Open the front cover on the server section, and set the MODE switch to the "STOP" position. (2) Set the RESET switch to the "SEL." position. (3) After ... More Details >>
- No：38044
- Release Date：2021/02/25 17:54
- Category： Energy Saving Data Collecting Servers
As to timing for outputting data file into the SD memory card.

EMU4-LM outputs data file at following timing. 1. When inserting the SD memory card while operating. 2. When power is ON in a state of the SD memory ca... More Details >>
- No：22133
- Release Date：2018/08/27 16:41
- Category： Energy Measuring Units
Extension of current sensor cable (EcoMonitorPlus/Light).

Use an extension cable (Model: EMU2-CB-T1M / EMU2-CB-T5M/EMU2-CB-T10M / EMU2-CB-T1MS / EMU2-CB-T5MS / EMU2-CB-T10MS) for extending the cable between EcoMonit... More Details >>
- No：22118
- Release Date：2018/08/27 16:41
- Update：2018/09/07 11:47
- Category： Energy Measuring Units
MEASURE LED not blink (EcoMonitorPlus).

MEASURE LED lights while measuring electric power over 0.4% of the total load power. Check below points: 1. Is voltage wiring connected? 2. Are the trans... More Details >>
- No：22144
- Release Date：2018/08/27 16:41
- Category： Energy Measuring Units
As to ejecting an SD memory card.

The timing for ejecting an SD memory card is specified as below table according to the state of the [SD C.] LED of the Logging Unit for the Energy Measuring ... More Details >>
- No：22121
- Release Date：2018/08/27 16:41
- Update：2018/09/07 13:04
- Category： Energy Measuring Units
As to action upon memory shortage of the SD memory card.

It will stop outputting logging data from the Logging Unit. [SD C.] LED will be high-speed blinking （repeat of 0.25sec ON → 0.25sec OFF）. Backup the data ... More Details >>
- No：22135
- Release Date：2018/08/27 16:41
- Category： Energy Measuring Units
EcoWebServerIII's rated voltage value setting with VT connections

For 3P4W circuits, set the VT primary voltage value (between L and N). Except for 3P4W circuits, set the VT primary voltage value (between L and L). <Re... More Details >>
- No：38040
- Release Date：2021/02/25 17:54
- Category： Energy Measuring Units , Energy Saving Data Collecting Servers

31-40 of Total 47

Inquiries

page top