The built-in motion function of the MX-F Model is programmed using motion control FB, wheareas the FX5-40/80SSC-G of the

It's possible. In GX Works3, select [Project] → [Change Module Type/Operation Mode], and select the Series: MX controlle

You can check the LOT. on the front of the controller or the nameplate on the right side. Verifying on the front of the

Extended extension cable for MX-F Model: FX5-30 EC/FX5-65 EC can be used. However, only one extended extension cable is

The MX-F Model only supports subroutine type FB. Please note that macro type FB is not supported.

The following programming languages are supported. ・Ladder diagram (LD) ・Structured text (ST) ・Function block diagram (F

It is possible to connect the I/O Module of the MX-F Model to the extension cable type I/O Module of the iQ-F series. T

Please refer to the below Technical bulletin for the functional differences between the MX-F model and the iQ-F series.

Programming is possible with GX Works3. The supported version is 1.115V or later.

On the MX-F Model, the Performance Monitor function enables Program List Monitor. The operation cycle and load status o

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Automation Controllers MELSEC

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Programmable Automation Controllers MELSEC

MELSEC MX Controller Engineering Software

FAQ within [ Programmable Automation Controllers MELSEC ]

11-20 of Total 28

prev 2 / 3page next

Regarding the built-in motion function

The built-in motion function of the MX-F Model is programmed using motion control FB, wheareas the FX5-40/80SSC-G of the iQ-F series is programmed using buff... More Details >>
- No：44970
- Release Date：2025/06/18 14:38
- Category： MELSEC MX Controller MX-F Model
Regarding iQ-F Series Project Conversion

It's possible. In GX Works3, select [Project] → [Change Module Type/Operation Mode], and select the Series: MX controller, Type/Model: MXF100, Number of Axes... More Details >>
- No：44987
- Release Date：2025/05/08 09:09
- Category： MELSEC MX Controller MX-F Model
Regarding how to check the date of manufacture

You can check the LOT. on the front of the controller or the nameplate on the right side. Verifying on the front of the Controller Nameplate verification... More Details >>
- No：44968
- Release Date：2025/05/08 09:05
- Category： MELSEC MX Controller MX-F Model
Regarding use of extended extension cable

Extended extension cable for MX-F Model: FX5-30 EC/FX5-65 EC can be used. However, only one extended extension cable is allowed per system. *Extended extens... More Details >>
- No：44985
- Release Date：2025/05/08 09:07
- Category： MELSEC MX Controller MX-F Model
Regarding the available FB compilation methods

The MX-F Model only supports subroutine type FB. Please note that macro type FB is not supported. More Details >>
- No：44975
- Release Date：2025/05/08 09:07
- Category： MELSEC MX Controller MX-F Model
Regarding supported programming languages

The following programming languages are supported. ・Ladder diagram (LD) ・Structured text (ST) ・Function block diagram (FBD/LD) More Details >>
- No：44972
- Release Date：2025/05/08 09:06
- Category： MELSEC MX Controller MX-F Model
Regarding connectable I/O Modules

It is possible to connect the I/O Module of the MX-F Model to the extension cable type I/O Module of the iQ-F series. To connect an extension cable type I/O... More Details >>
- No：44965
- Release Date：2025/05/08 09:06
- Category： MELSEC MX Controller MX-F Model
Regarding functional differences from iQ-F Series

Please refer to the below Technical bulletin for the functional differences between the MX-F model and the iQ-F series. [Technical bulletin] ・Differences ... More Details >>
- No：44979
- Release Date：2025/06/18 14:38
- Category： MELSEC MX Controller MX-F Model
Regarding programming tools

Programming is possible with GX Works3. The supported version is 1.115V or later. More Details >>
- No：44962
- Release Date：2025/05/08 09:05
- Category： MELSEC MX Controller MX-F Model
Regarding the Program List Monitor

On the MX-F Model, the Performance Monitor function enables Program List Monitor. The operation cycle and load status of the core can be visualized. More Details >>
- No：44989
- Release Date：2025/05/08 09:08
- Category： MELSEC MX Controller MX-F Model

11-20 of Total 28

Inquiries

page top