Extended extension cable for MX-F Model: FX5-30 EC/FX5-65 EC can be used. However, only one extended extension cable is

The maximum number of input/output points is 512. The number of remote I/O points is not limited, but can be used within

It's possible. In GX Works3, select [Project] → [Change Module Type/Operation Mode], and select the Series: MX controlle

The MX-F Model also supports the built-in positioning function. The number of control axes is now 4, and PULSE/SIGN and

Port 1 becomes the CC-Link IE TSN, and port 2 can be switched between Ethernet and CC-Link IE TSN. To use port 2 as an E

The following programming languages are supported. ・Ladder diagram (LD) ・Structured text (ST) ・Function block diagram (F

You can check the LOT. on the front of the controller or the nameplate on the right side. Verifying on the front of the

The MX-F Model has two built-in Ethernet ports. In the following, the Ethernet port (P1) is referred to as P1 and the Et

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Automation Controllers MELSEC > MELSEC MX Controller MX-F Model

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ MELSEC MX Controller MX-F Model ]

21-28 of Total 28

prev 3 / 3page next

Regarding use of extended extension cable

Extended extension cable for MX-F Model: FX5-30 EC/FX5-65 EC can be used. However, only one extended extension cable is allowed per system. *Extended extens... More Details >>
- No：44985
- Release Date：2025/05/08 09:07
Regarding maximum number of input/output points

The maximum number of input/output points is 512. The number of remote I/O points is not limited, but can be used within the specification range of each int... More Details >>
- No：44971
- Release Date：2025/05/08 09:07
Regarding iQ-F Series Project Conversion

It's possible. In GX Works3, select [Project] → [Change Module Type/Operation Mode], and select the Series: MX controller, Type/Model: MXF100, Number of Axes... More Details >>
- No：44987
- Release Date：2025/05/08 09:09
Regarding the built-in positioning function

The MX-F Model also supports the built-in positioning function. The number of control axes is now 4, and PULSE/SIGN and CW/CCW are supported. The maximum f... More Details >>
- No：44978
- Release Date：2025/05/08 09:08
Regarding built-in ethernet port differences

Port 1 becomes the CC-Link IE TSN, and port 2 can be switched between Ethernet and CC-Link IE TSN. To use port 2 as an Ethernet port, set the Built-in Netwo... More Details >>
- No：44969
- Release Date：2025/05/08 09:05
Regarding supported programming languages

The following programming languages are supported. ・Ladder diagram (LD) ・Structured text (ST) ・Function block diagram (FBD/LD) More Details >>
- No：44972
- Release Date：2025/05/08 09:06
Regarding how to check the date of manufacture

You can check the LOT. on the front of the controller or the nameplate on the right side. Verifying on the front of the Controller Nameplate verification... More Details >>
- No：44968
- Release Date：2025/05/08 09:05
Regarding the default IP address

The MX-F Model has two built-in Ethernet ports. In the following, the Ethernet port (P1) is referred to as P1 and the Ethernet port (P2) as P2. *P2 selects... More Details >>
- No：44981
- Release Date：2025/05/08 09:02

21-28 of Total 28

Inquiries

page top