Cause:The fuse (4A fuse) installed at the bottom of the 24 V power supply circuit in the controller may have blown out.F

Cause:Wire breakage on the hand signal line. The electronic hand controller(manufactured by TAIYO Ltd.) has failed. Faul

Cause:Incorrect breaker selection(current capacity/drive purpose, etc.). Leakage current due to electrically conductive

Cause:An air leak/break in the piping. The solenoid bulb has failed. Wire breakage on the hand signal line. Hand signal

Cause:Deterioration in the packing. Scaling on the packing. Using a highly permeable cutting oil. An environment that ex

Cause:The fuse installed in the controller may have blown out. For the fuse blowout, there may be a ground fault or shor

Cause:[Occurs only when operating manually]•T/B operation error.•The enabling device input is open.[Occurs when operatin

Cause:CPU has not started up properly.There is no power supply.An instantaneous power cut exceeding the specification le

Cause:Unusual noises can be caused by friction between movable parts, deformed parts, foreign matters getting inside, an

Cause: AC line inside the controller may have detected the abnormalities. Measures: Check that the primary s

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Robots > Industrial/Collaborative Robots-MELFA > Horizontal type robot

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ Horizontal type robot ]

1-10 of Total 18

prev 1 / 2page next

The T/B does not display anything.

Cause:The fuse (4A fuse) installed at the bottom of the 24 V power supply circuit in the controller may have blown out.For the fuse blowout, the emergency st... More Details >>
- No：23184
- Release Date：2018/09/07 16:09
The hand does not move properly (Electric operated hand).

Cause:Wire breakage on the hand signal line. The electronic hand controller(manufactured by TAIYO Ltd.) has failed. Faulty connection in the cables that run ... More Details >>
- No：23177
- Release Date：2018/09/07 16:09
The leakage current breaker trips.

Cause:Incorrect breaker selection(current capacity/drive purpose, etc.). Leakage current due to electrically conductive foreign matters(oil/moisture) getting... More Details >>
- No：23173
- Release Date：2018/09/07 16:09
The hand does not move properly (air hand).

Cause:An air leak/break in the piping. The solenoid bulb has failed. Wire breakage on the hand signal line. Hand signal line short circuitThe hand IF card ha... More Details >>
- No：23176
- Release Date：2018/09/07 16:09
Breaker trips/overcurrent error occurs.

Cause:Deterioration in the packing. Scaling on the packing. Using a highly permeable cutting oil. An environment that exceeds the IP functionality. Measures:... More Details >>
- No：23175
- Release Date：2018/09/07 16:09
The T/B does not display anything.

Cause:The fuse installed in the controller may have blown out. For the fuse blowout, there may be a ground fault or short circuit in the T/B cable. The T/B m... More Details >>
- No：23180
- Release Date：2018/09/07 16:09
Brake is not working properly.

Cause:[Occurs only when operating manually]•T/B operation error.•The enabling device input is open.[Occurs when operating manually and automatically]•Faulty ... More Details >>
- No：23183
- Release Date：2018/09/07 16:09
Operation panel does not display anything.

Cause:CPU has not started up properly.There is no power supply.An instantaneous power cut exceeding the specification level may have occurred.Measures:Check ... More Details >>
- No：23181
- Release Date：2018/09/07 16:09
An unusual noise can be heard (from the robot arm).

Cause:Unusual noises can be caused by friction between movable parts, deformed parts, foreign matters getting inside, and defects in belt tension.An unusual ... More Details >>
- No：23167
- Release Date：2018/09/07 16:09
The operation panel does not light up. Although the T/B has got the electricity, the operation of T/B cannot be done.

Cause: AC line inside the controller may have detected the abnormalities. Measures: Check that the primary side’s power supply voltage is being su... More Details >>
- No：23182
- Release Date：2018/09/07 16:09
- Update：2018/10/03 14:52

1-10 of Total 18

Inquiries

page top