MX Component and EXCEL are required.

No.It is necessary to configure one port to use the MELSOFT connection.

Uncheck "Check battery", an item of "Error Check", in the [PLC RAS setting] ([PLC Parameter] -> [PLC RAS setting]).

The following figure shows the basic configuration. When a control system Ethernet module is faulty or disconnected,

No. Switch the target memory for PLC Data and read the file registers alone.

Create global device comments and local device comments in respective languages.The device comments can be switched in [

Totem pole output encoders cannot be connected to QD62.The following types of encoders can be connected.- Open collector

The merits are as follows. (1) Downsized device The volume ratio is 1 to 10 in comparison with the VME card rack

(1) If the A/D conversion enable signal is kept ON, conversion processing is kept performed. Once conversion proces

You need to set the number of extension base units with the connector for setting the number of extension base units.For

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC > MELSEC-Q Series

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ MELSEC-Q Series ]

41-50 of Total 213

prev 5 / 22page next

Software required for MX Sheet

MX Component and EXCEL are required. More Details >>
- No：22646
- Release Date：2018/09/03 17:29
Open setting of the built-in Ethernet port QCPU

No.It is necessary to configure one port to use the MELSOFT connection. More Details >>
- No：22648
- Release Date：2018/09/03 17:29
Battery-less operation

Uncheck "Check battery", an item of "Error Check", in the [PLC RAS setting] ([PLC Parameter] -> [PLC RAS setting]). More Details >>
- No：22681
- Release Date：2018/09/03 17:29
- Update：2018/09/21 14:12
Ethernet system configuration of a redundant system

The following figure shows the basic configuration. When a control system Ethernet module is faulty or disconnected, the system is switched at a disco... More Details >>
- No：22718
- Release Date：2018/09/03 17:29
- Update：2018/09/18 11:45
Reading file registers simultaneously with the program, parameters, and other data in GX Works2

No. Switch the target memory for PLC Data and read the file registers alone. More Details >>
- No：22616
- Release Date：2018/09/03 17:29
Creating comments both in English and in Japanese

Create global device comments and local device comments in respective languages.The device comments can be switched in [Options] -> [Tool]. More Details >>
- No：22620
- Release Date：2018/09/03 17:29
Whether or not totem pole output type encoders are connected

Totem pole output encoders cannot be connected to QD62.The following types of encoders can be connected.- Open collector output type encoders- CMOS level vol... More Details >>
- No：22641
- Release Date：2018/09/03 17:29
Replacing personal computers with C Controller modules

The merits are as follows. (1) Downsized device The volume ratio is 1 to 10 in comparison with the VME card rack (6U) type. (2) Long-term stable supply... More Details >>
- No：22706
- Release Date：2018/09/03 17:29
- Update：2018/09/21 14:33
Change timing of the status of A/D conversion module's I/O signals

(1)If the A/D conversion enable signal is kept ON, conversion processing is kept performed. Once conversion processing is successfully performed, A/D conve... More Details >>
- No：22710
- Release Date：2018/09/03 17:29
- Update：2018/09/21 15:12
Hardware setting for using Q series extension base units

You need to set the number of extension base units with the connector for setting the number of extension base units.For details, refer to the following.SH-0... More Details >>
- No：22721
- Release Date：2018/09/03 17:29

41-50 of Total 213

Inquiries

page top