It is the number of data collected before and after a trigger occurrence.

To send simultaneous broadcast using UDP, set the parameters as follows.- Destination IP Address: FF.FF.FF.FFh - Destina

This adapter is used to add a serial port to the L series CPU. It is not a serial communication module. It is used for s

Yes. They have the same pin layout.

The heater disconnection detection function monitors the heater current on the transistor output. If no current flows w

Use the following power supply module with an input power of 200 VAC for compliance with SEMI-F47. - Power supply module

No. It is necessary to configure one port to use the MELSOFT connection.

To prevent an LED from turning on when an error occurs, set 0 to the relevant factor number setting area (4 bits for eac

The values are updated at the timing described below. - Current feed value: 0.9 ms - Machine feed value: 0.9 ms

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC > MELSEC-L Series

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ MELSEC-L Series ]

91-100 of Total 105

prev 10 / 11page next

Number of records in LCPU logging function

It is the number of data collected before and after a trigger occurrence. More Details >>
- No：22794
- Release Date：2018/09/03 17:30
Simultaneous broadcast transmission setting for built-in Ethernet port LCPU

To send simultaneous broadcast using UDP, set the parameters as follows.- Destination IP Address: FF.FF.FF.FFh - Destination Port Number: Other than FFFFh (S... More Details >>
- No：22785
- Release Date：2018/09/03 17:30
Application of RS-232 adapter L6ADP-R2

This adapter is used to add a serial port to the L series CPU. It is not a serial communication module. It is used for serial communication between a device ... More Details >>
- No：22778
- Release Date：2018/09/03 17:30
FNC connector pin layout in L series I/O module and Q series I/O module

Yes. They have the same pin layout. More Details >>
- No：22774
- Release Date：2018/09/03 17:30
Loop disconnection detection function and heater disconnection detection function of temperature control module

The heater disconnection detection function monitors the heater current on the transistor output. If no current flows when the transistor is ON, it is consi... More Details >>
- No：22773
- Release Date：2018/09/03 17:30
- Update：2018/09/22 10:58
Compliance with SEMI-F47 for L series power supply module

Use the following power supply module with an input power of 200 VAC for compliance with SEMI-F47. - Power supply module: L61PWith an input power of 100 VAC,... More Details >>
- No：22768
- Release Date：2018/09/03 17:30
Open setting of LCPU

No. It is necessary to configure one port to use the MELSOFT connection. More Details >>
- No：22765
- Release Date：2018/09/03 17:30
Operation during power failure

It stops during execution. More Details >>
- No：22764
- Release Date：2018/09/03 17:30
Method to prevent the BAT.LED from turning on

To prevent an LED from turning on when an error occurs, set 0 to the relevant factor number setting area (4 bits for each) in SD207 to SD209. To disable the ... More Details >>
- No：22754
- Release Date：2018/09/03 17:29
Update timing of LD75 current feed value and machine feed value

The values are updated at the timing described below. - Current feed value: 0.9 ms - Machine feed value: 0.9 ms More Details >>
- No：22748
- Release Date：2018/09/03 17:29

91-100 of Total 105

Inquiries

page top