The QJ71C24N series modules can be accessed using A-compatible 1C frames, but the following restrictions are imposed. Th

Carry out DTR and DSR wiring that returns signals on QJ71C24N(-R2).

Connect terminating resistors to both ends of physical cables.A master station is not necessarily required to be connect

Short between SDA and RDA and between SDB and RDB, and then connect them to + (Data-A) and - (Data-B) on the external de

The resistance value is 110 ohm, 1/2 W.

"The CD terminal is not checked" has been set by default.

Major differences are shown below. - AJ65SBTB1-16DT1 <Input specifications> - Rated input current approx. 5 mA -

A terminating resistor must be connected to the interface in order to reduce signal reflections thus preventing the sign

For CPU modules with 8192 I/O device points (X/Y0 to 1FFF), X/Y1000 and greater can be set as refresh devices.

Cyclic data is sometimes separated into new and old data by two words (32 bits) with auto refresh timing. Checking "Bloc

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC > Network related products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ Network related products ]

1-10 of Total 110

prev 1 / 11page next

Whether or not MC protocol frames can be used after A1SJ71UC24 is replaced with QJ71C24N

The QJ71C24N series modules can be accessed using A-compatible 1C frames, but the following restrictions are imposed. The access is limited to the devices wi... More Details >>
- No：22970
- Release Date：2018/09/03 17:31
Connecting QJ71C24N to an external device that has no DTR signal

Carry out DTR and DSR wiring that returns signals on QJ71C24N(-R2). More Details >>
- No：23039
- Release Date：2018/09/03 17:31
Connecting terminating resistors for CC-Link communication

Connect terminating resistors to both ends of physical cables.A master station is not necessarily required to be connected to either end of its network. More Details >>
- No：23046
- Release Date：2018/09/03 17:31
RS-485 connection between LJ71C24 and an external device

Short between SDA and RDA and between SDB and RDB, and then connect them to + (Data-A) and - (Data-B) on the external device. More Details >>
- No：23048
- Release Date：2018/09/03 17:31
Terminating resistors for RS-485 communication of LJ71C24

The resistance value is 110 ohm, 1/2 W. More Details >>
- No：22999
- Release Date：2018/09/03 17:31
- Update：2018/10/03 15:25
CD terminal setting of the QJ71C24N

"The CD terminal is not checked" has been set by default. More Details >>
- No：23065
- Release Date：2018/09/03 17:31
Difference between AJ65SBTB1-16DT1 and AJ65SBTB1-16DT2

Major differences are shown below. - AJ65SBTB1-16DT1 - Rated input current approx. 5 mA - ON voltage/ON current 15 VDC or higher/3.0 mA or higher - O... More Details >>
- No：22972
- Release Date：2018/09/03 17:31
- Update：2018/09/25 17:04
Terminating resistors for QJ71C24N

A terminating resistor must be connected to the interface in order to reduce signal reflections thus preventing the signal instabilities. More Details >>
- No：22982
- Release Date：2018/09/03 17:31
Refresh devices

For CPU modules with 8192 I/O device points (X/Y0 to 1FFF), X/Y1000 and greater can be set as refresh devices. More Details >>
- No：23014
- Release Date：2018/09/03 17:31
Refresh timing of bit data and word data in the same CC-Link station

Cyclic data is sometimes separated into new and old data by two words (32 bits) with auto refresh timing. Checking "Block data assurance per station" of the ... More Details >>
- No：23058
- Release Date：2018/09/03 17:31

1-10 of Total 110

Inquiries

page top