The data link status is stored in SW80 to SW83.Each bit corresponds to a station number and a bit turns ON if the corres

No, it is unnecessary. Terminating resistors are only required at both ends of the network.

Check the following signals.- Module error signal : X0- Host data link status signal: X1- Other station data link s

There are two types of terminating resistors for CC-Link communication. Both two types are packaged with a CC-Link maste

QJ61BT11N supports Version 2 (expanded cyclic setting), the setting for refreshing/forced clearing a slave station data

- T-branch T-branch is a connection type that branches one line from a main line. To establish a T-branch CC-Li

The error code indicates a WDT (watchdog timer) error. It is determined as the cause that the MELSECNET/H driver cannot

The value depends on the type of cable in use. - Ver.1.10-compatible CC-Link dedicated cables: 110 ohm, 1/2W - CC-Link d

The CC-Link IE Control Network is a high-capacity controller network whose maximum number of link points is 128k words.

M8029 (Instruction execution complete flag) is shared with multiple instructions. To obtain an execution completion resu

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC > Network related products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ Network related products ]

101-110 of Total 110

prev 11 / 11page next

How to check link errors in CC-Link slave stations

The data link status is stored in SW80 to SW83.Each bit corresponds to a station number and a bit turns ON if the corresponding station causes a data link er... More Details >>
- No：23031
- Release Date：2018/09/03 17:31
Necessity of terminating resistors in CC-Link communication

No, it is unnecessary. Terminating resistors are only required at both ends of the network. More Details >>
- No：22966
- Release Date：2018/09/03 17:31
CC-Link signals checked when an error occurs

Check the following signals.- Module error signal : X0- Host data link status signal: X1- Other station data link status signal: X3 More Details >>
- No：23021
- Release Date：2018/09/03 17:31
Terminating resistors for CC-Link communication

There are two types of terminating resistors for CC-Link communication. Both two types are packaged with a CC-Link master/local module. (1) 110 ohm, 1/2W (B... More Details >>
- No：22963
- Release Date：2018/09/03 17:31
- Update：2018/09/26 14:47
Difference between QJ61BT11 and QJ61BT11N

QJ61BT11N supports Version 2 (expanded cyclic setting), the setting for refreshing/forced clearing a slave station data when the switch on a programmable con... More Details >>
- No：22964
- Release Date：2018/09/03 17:31
- Update：2018/09/25 13:16
T-branch connection and star topology for CC-Link networks

- T-branch T-branch is a connection type that branches one line from a main line. To establish a T-branch CC-Link network, use the repeater module AJ65S... More Details >>
- No：23024
- Release Date：2018/09/03 17:31
- Update：2018/09/26 10:00
Remedies for WDT errors on a MELSECNET/H board

The error code indicates a WDT (watchdog timer) error. It is determined as the cause that the MELSECNET/H driver cannot work due to a computer or OS hang, or... More Details >>
- No：22969
- Release Date：2018/09/03 17:31
Resistor value for CC-Link cables

The value depends on the type of cable in use. - Ver.1.10-compatible CC-Link dedicated cables: 110 ohm, 1/2W - CC-Link dedicated cables (Version 1.00): 110... More Details >>
- No：22983
- Release Date：2018/09/03 17:31
- Update：2018/10/03 14:42
Differences between CC-Link IE Control Network and CC-Link IE Field Network

The CC-Link IE Control Network is a high-capacity controller network whose maximum number of link points is 128k words. The CC-Link IE Field Network is an al... More Details >>
- No：23085
- Release Date：2018/09/03 17:31
How to use M8029

M8029 (Instruction execution complete flag) is shared with multiple instructions. To obtain an execution completion result of a specific instruction, insert... More Details >>
- No：24775
- Release Date：2019/02/27 15:34

101-110 of Total 110

Inquiries

page top