If the remote net Ver.1 mode is used, each station number is given fixed buffer memory addresses.If the remote net Ver.2

The following shows the relations between CC-Link terminals and signal lines. - DA : Blue - DB : White - DG : Yellow

The MODE switch can set the following modes.- 0 to 4: Online mode- 5 to 9: Line test mode- A to E: Hardware test modeEac

Major differences are shown below. - AJ65SBTB1-32DT- Leakage current at OFF 0.25 mA or lower- Protection function (overl

The QJ71C24N series modules can be accessed using A-compatible 1C frames, but the following restrictions are imposed. Th

To assure 32-bit data, "Network Range Assignment" of the control station must satisfy the following conditions.(1) The s

The receive data length of the variable is specified in bytes.

To pursue high speeds, the CC-Link IE Field Network applies a communication control method different from that applied t

The I/O numbers used for I/O modules and intelligent function modules cannot be used as refresh targets for RX/RY. Use t

Short between SDA and RDA and between SDB and RDB, and then connect them to + (Data-A) and - (Data-B) on the external de

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC > Network related products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ Network related products ]

21-30 of Total 110

prev 3 / 11page next

Buffer memory addresses of CC-Link modules

If the remote net Ver.1 mode is used, each station number is given fixed buffer memory addresses.If the remote net Ver.2 mode is used, different buffer memor... More Details >>
- No：22992
- Release Date：2018/09/03 17:31
Relation between CC-Link terminals and signal lines

The following shows the relations between CC-Link terminals and signal lines. - DA : Blue -DB: White -DG: Yellow More Details >>
- No：23077
- Release Date：2018/09/03 17:31
- Update：2018/09/26 13:11
MODE switch setting for QJ61BT11N

The MODE switch can set the following modes.- 0 to 4: Online mode- 5 to 9: Line test mode- A to E: Hardware test modeEach mode in ascending order of set valu... More Details >>
- No：23025
- Release Date：2018/09/03 17:31
Difference between AJ65SBTB1-32DT and AJ65SBTB1-32DT2

Major differences are shown below. - AJ65SBTB1-32DT- Leakage current at OFF 0.25 mA or lower- Protection function (overload protection, overvoltage protectio... More Details >>
- No：22985
- Release Date：2018/09/03 17:31
Whether or not MC protocol frames can be used after A1SJ71UC24 is replaced with QJ71C24N

The QJ71C24N series modules can be accessed using A-compatible 1C frames, but the following restrictions are imposed. The access is limited to the devices wi... More Details >>
- No：22970
- Release Date：2018/09/03 17:31
32-bit data assurance

To assure 32-bit data, "Network Range Assignment" of the control station must satisfy the following conditions.(1) The start device No. of LB is a multiple o... More Details >>
- No：23052
- Release Date：2018/09/03 17:31
Unit of the receive data length used by the QJ71C24N series pre-defined protocol support function

The receive data length of the variable is specified in bytes. More Details >>
- No：23037
- Release Date：2018/09/03 17:31
Connecting the CC-Link IE Field Network with a personal computer

To pursue high speeds, the CC-Link IE Field Network applies a communication control method different from that applied to the Ethernet communication for pers... More Details >>
- No：23012
- Release Date：2018/09/03 17:31
CC-Link master modules' start I/O No. and refresh devices RX/RY

The I/O numbers used for I/O modules and intelligent function modules cannot be used as refresh targets for RX/RY. Use the I/O numbers greater than those use... More Details >>
- No：22997
- Release Date：2018/09/03 17:31
RS-485 connection between QJ71C24N and an external device

Short between SDA and RDA and between SDB and RDB, and then connect them to + (Data-A) and - (Data-B) on the external device. More Details >>
- No：22986
- Release Date：2018/09/03 17:31

21-30 of Total 110

Inquiries

page top