Use the plate terminal packaged with the module. The size of the plate terminal is 1.0 mm wide with a thickness of 0.8 m

The receive data length of the variable is specified in bytes.

A CC-Link slave station number can be skipped by assigning the skipped number to a reserved station. A reserved station

The overall cable distance and station-to-station distance depend on the version and the transmission speed. Figure 1 s

The MODE switch can set the following modes.- 0 to 4: Online mode- 5 to 9: Line test mode- A to E: Hardware test modeEac

Check the following signals.- Module error signal : X0- Host data link status signal: X1- Other station data link s

To pursue high speeds, the CC-Link IE Field Network applies a communication control method different from that applied t

The number of disconnections detected can be checked by reading the buffer memory address 5203H (Disconnection detection

Major differences are shown below. - AJ65SBTB1-32DT- Leakage current at OFF 0.25 mA or lower- Protection function (overl

Set the number of occupied stations for a CC-Link local station using the programming tool, GX Developer or GX Works2. S

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC > Network related products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ Network related products ]

31-40 of Total 110

prev 4 / 11page next

Applicable size for plug-in connector socket block on QJ71C24N-R4

Use the plate terminal packaged with the module. The size of the plate terminal is 1.0 mm wide with a thickness of 0.8 mm. More Details >>
- No：23043
- Release Date：2018/09/03 17:31
Unit of the receive data length used by the QJ71C24N series pre-defined protocol support function

The receive data length of the variable is specified in bytes. More Details >>
- No：23037
- Release Date：2018/09/03 17:31
Setting required to skip CC-Link slave station numbers

A CC-Link slave station number can be skipped by assigning the skipped number to a reserved station. A reserved station is counted as one of all the connecte... More Details >>
- No：23029
- Release Date：2018/09/03 17:31
Overall cable distance and station-to-station distance in CC-Link networks

The overall cable distance and station-to-station distance depend on the version and the transmission speed. Figure 1 shows the case with Ver.1.10-compatibl... More Details >>
- No：23028
- Release Date：2018/09/03 17:31
- Update：2018/09/26 10:14
MODE switch setting for QJ61BT11N

The MODE switch can set the following modes.- 0 to 4: Online mode- 5 to 9: Line test mode- A to E: Hardware test modeEach mode in ascending order of set valu... More Details >>
- No：23025
- Release Date：2018/09/03 17:31
CC-Link signals checked when an error occurs

Check the following signals.- Module error signal : X0- Host data link status signal: X1- Other station data link status signal: X3 More Details >>
- No：23021
- Release Date：2018/09/03 17:31
Connecting the CC-Link IE Field Network with a personal computer

To pursue high speeds, the CC-Link IE Field Network applies a communication control method different from that applied to the Ethernet communication for pers... More Details >>
- No：23012
- Release Date：2018/09/03 17:31
Detecting the number of disconnections when using QJ71E71-100

The number of disconnections detected can be checked by reading the buffer memory address 5203H (Disconnection detection count). Disconnections are detected ... More Details >>
- No：23003
- Release Date：2018/09/03 17:31
- Update：2018/09/25 17:49
Difference between AJ65SBTB1-32DT and AJ65SBTB1-32DT2

Major differences are shown below. - AJ65SBTB1-32DT- Leakage current at OFF 0.25 mA or lower- Protection function (overload protection, overvoltage protectio... More Details >>
- No：22985
- Release Date：2018/09/03 17:31
How to set the numbers of occupied stations for CC-Link local stations

Set the number of occupied stations for a CC-Link local station using the programming tool, GX Developer or GX Works2. Set the number for "Number of Occupied... More Details >>
- No：22980
- Release Date：2018/09/03 17:31

31-40 of Total 110

Inquiries

page top