X and Y assignments are as follows.- X0 to XF- Y10 to Y1F

Major differences in input specifications are shown below. - AJ65SBTB1-16DT - Rated input current approx. 7 mA - ON vol

Ground FG in each station. SLD and FG are internally short-circuited.

The routing parameter settings are required for transient transmission to the CPU module with another network No. The re

For "Remote Net(Ver.2 Mode)", the number of remote I/O's remote registers (RWw, RWr) is "0 Point".

The following shows the major differences. - AJ65SBTB1-16TE - 1-wire terminal block, 1-common type - Maximum load c

- If the Network Parameter is used Make "Station Information Setting". - If the parameter is set using a dedicated

No, it is unnecessary. Terminating resistors are only required at both ends of the network.

The resistance value is 110 ohm, 1/2 W.

To pursue high speeds, the CC-Link IE Field Network applies a communication control method different from that applied t

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC > Network related products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ Network related products ]

61-70 of Total 110

prev 7 / 11page next

Assigning X and Y signals of AJ65SBTB1-32DT

X and Y assignments are as follows.- X0 to XF- Y10 to Y1F More Details >>
- No：23034
- Release Date：2018/09/03 17:31
Difference between AJ65SBTB1-16DT and AJ65SBTB1-16DT1

Major differences in input specifications are shown below. - AJ65SBTB1-16DT - Rated input current approx. 7 mA - ON voltage/ON current 14 VDC or higher/... More Details >>
- No：23035
- Release Date：2018/09/03 17:31
- Update：2018/09/26 10:24
SLD and FG wiring for CC-Link networks

Ground FG in each station. SLD and FG are internally short-circuited. More Details >>
- No：23020
- Release Date：2018/09/03 17:31
Settings required for transient transmission

The routing parameter settings are required for transient transmission to the CPU module with another network No. The request source station, relay station,... More Details >>
- No：22995
- Release Date：2018/09/03 17:31
- Update：2018/09/25 17:40
Number of remote registers assigned to a remote I/O station

For "Remote Net(Ver.2 Mode)", the number of remote I/O's remote registers (RWw, RWr) is "0 Point". More Details >>
- No：22973
- Release Date：2018/09/03 17:31
Differences between the AJ65SBTB1-16TE and AJ65SBTB1B-16TE1

The following shows the major differences. -AJ65SBTB1-16TE - 1-wire terminal block, 1-common type - Maximum load current: 0.1 A/point -Protection fu... More Details >>
- No：23083
- Release Date：2018/09/03 17:31
- Update：2018/09/26 13:16
How to set CC-Link reserved stations

- If the Network Parameter is used Make "Station Information Setting". - If the parameter is set using a dedicated instruction Set the control data of... More Details >>
- No：22996
- Release Date：2018/09/03 17:31
- Update：2018/09/25 17:41
Necessity of terminating resistors in CC-Link communication

No, it is unnecessary. Terminating resistors are only required at both ends of the network. More Details >>
- No：22966
- Release Date：2018/09/03 17:31
Terminating resistors for RS-485 communication of QJ71C24N

The resistance value is 110 ohm, 1/2 W. More Details >>
- No：22978
- Release Date：2018/09/03 17:31
- Update：2018/10/03 15:48
Connecting the CC-Link IE Field Network with a personal computer

To pursue high speeds, the CC-Link IE Field Network applies a communication control method different from that applied to the Ethernet communication for pers... More Details >>
- No：23012
- Release Date：2018/09/03 17:31

61-70 of Total 110

Inquiries

page top