No, the operation speed is not changed by changing the indirectly specified value.To change the speed during operation,

No, the speed limit cannot be changed during operation.

The rapid stop deceleration time of parameter block is applied.However, when the rapid stop deceleration time is set in

No, there is no impact on the command speed.However, the actual acceleration/deceleration time are affected by the chang

Both OUT and SET instructions set the device by completion of condition.However, if not completion of condition, OUT ins

To reflect the change, set "[PA14] Rotation direction selection/traveldirection selection" and cycle the servo amplifier

Set "[PA04] Function selection A-1" to "_1_ _h: Invalid".(Note): When using Q17nCPUN, set "Servo amplifier parameter 23

Change the direction with "[PA14] Rotation direction selection/travel direction selection".

Specify the target axes during operation, and execute the following speed change request instruction. (1) Motion SFC pro

Minor error 197AH (Home position return zero not passed) occurs in the following case:"[St.1066] zero pass" is OFF when

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Motion Controllers > MELSEC iQ-R Series > Motion Controllers

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Motion Controllers

RnMTCPU(13)

FAQ within [ Motion Controllers ]

1-10 of Total 13

prev 1 / 2page next

Speed change

No, the operation speed is not changed by changing the indirectly specified value.To change the speed during operation, use CHGV instruction. More Details >>
- No：23555
- Release Date：2018/09/14 15:09
- Category： RnMTCPU , Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Speed limit value change during operation

No, the speed limit cannot be changed during operation. More Details >>
- No：23571
- Release Date：2018/09/14 15:09
- Category： RnMTCPU , Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Rapid stop signal

The rapid stop deceleration time of parameter block is applied.However, when the rapid stop deceleration time is set in the servo program, the value is enabl... More Details >>
- No：23557
- Release Date：2018/09/14 15:09
- Category： RnMTCPU , Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Speed limit value

No, there is no impact on the command speed.However, the actual acceleration/deceleration time are affected by the change. More Details >>
- No：23556
- Release Date：2018/09/14 15:09
- Category： RnMTCPU , Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
OUT instruction

Both OUT and SET instructions set the device by completion of condition.However, if not completion of condition, OUT instruction resets the device while SET ... More Details >>
- No：23553
- Release Date：2018/09/14 15:09
- Category： RnMTCPU , Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Servo motor rotation direction

To reflect the change, set "[PA14] Rotation direction selection/traveldirection selection" and cycle the servo amplifier or execute a home position return af... More Details >>
- No：23579
- Release Date：2018/09/14 15:09
- Category： RnMTCPU , Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Servo amplifier forced stop

Set "[PA04] Function selection A-1" to "_1_ _h: Invalid".(Note): When using Q17nCPUN, set "Servo amplifier parameter 23 (Optional function 1)"... More Details >>
- No：23567
- Release Date：2018/09/14 15:09
- Category： RnMTCPU , Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Motor rotation direction

Change the direction with "[PA14] Rotation direction selection/travel direction selection". More Details >>
- No：23554
- Release Date：2018/09/14 15:09
- Category： RnMTCPU , Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU
Speed change during operation

Specify the target axes during operation, and execute the following speed change request instruction. (1) Motion SFC program Speed change request CHGV，CHGVS ... More Details >>
- No：23575
- Release Date：2018/09/14 15:09
- Category： RnMTCPU
Minor error 197AH

Minor error 197AH (Home position return zero not passed) occurs in the following case:"[St.1066] zero pass" is OFF when the re-movement to the home position ... More Details >>
- No：23560
- Release Date：2018/09/14 15:09
- Category： RnMTCPU

1-10 of Total 13

Inquiries

page top