Regardless of setting, the value of the default digit length is replied. When the register address “1304” for 6-dig

It depends on the service conditions. Refer to the following guidelines. ① Contact output Contact output for ME9

They are the same dimensions. (Dimensions of an installation hole is 92 mm in length and width. Install this model two p

When [SET] is flashing, the “Setting Value Confirmation Mode” is selected. In this case, the set values cannot be change

This model has the test function of the communication operation. For detail, refer to User's Manual: Detailed Edition f

The acquired value by communication should be multiplied by the multiplying factor to change into the measurement va

It is not available. All configuration shall be conducted by the customer.

In a board installation state, the protection class is equivalent to IP50. This model is not waterproof.

Please check the register addresses. The register address for the present value of the power factor of each pha

Please check the register addresses. The register address for the present value of the power factor of each phase is “

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Low-voltage Power Distribution Products > Power Management Meters

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Power Management Meters

Electrical Indicators(57)

FAQ within [ Power Management Meters ]

21-30 of Total 57

prev 3 / 6page next

Active energy (lower digit indication) display upon communication test of MODBUS RTU/TCP communication (ME96SS series).

Regardless of setting, the value of the default digit length is replied. When the register address “1304” for 6-digit display is set, the value varies w... More Details >>
- No：22189
- Release Date：2018/08/27 16:41
- Update：2020/04/13 09:26
- Category： Electrical Indicators
Wire length for analog output and contact output（ME96SS series）

It depends on the service conditions. Refer to the following guidelines. ① Contact output Contact output for ME96 series is no-voltage "a" contact. The... More Details >>
- No：24807
- Release Date：2019/03/27 12:12
- Category： Electrical Indicators
Installation compatibility with ME96NSR (ME96SS series).

They are the same dimensions. (Dimensions of an installation hole is 92 mm in length and width. Install this model two points with mounting brackets.) More Details >>
- No：22160
- Release Date：2018/08/27 16:41
- Category： Electrical Indicators
Set values cannot be changed on the setting mode (ME96SS series).

When[SET] is flashing, the “Setting Value Confirmation Mode” is selected. In this case, the set values cannot be changed. Pressing the buttons of the “Set” ... More Details >>
- No：22168
- Release Date：2018/08/27 16:41
- Update：2020/04/10 16:22
- Category： Electrical Indicators
Validation method for communication function (ME96SS series).

This model has the test function of the communication operation. For detail, refer to User's Manual: Detailed Edition for setting. More Details >>
- No：22180
- Release Date：2018/08/27 16:41
- Category： Electrical Indicators
Acquired values through MODBUS RTU.

The acquired value by communication should be multiplied by the multiplying factor to change into the measurement value. Please refer to Section 7.3 of ... More Details >>
- No：22183
- Release Date：2018/08/27 16:41
- Update：2020/04/13 09:13
- Category： Electrical Indicators
Setting upon delivery (ME96SS series).

It is not available. All configuration shall be conducted by the customer. More Details >>
- No：22149
- Release Date：2018/08/27 16:41
- Update：2020/04/10 15:49
- Category： Electrical Indicators
IP protection class (ME96SS series).

In a board installation state, the protection class is equivalent to IP50. This model is not waterproof. More Details >>
- No：22158
- Release Date：2018/08/27 16:41
- Update：2020/04/10 16:13
- Category： Electrical Indicators
The power factor does not match the indication values through MODBUS.

Please check the register addresses. The register address for the present value of the power factor of each phase is “0789”. There are the register... More Details >>
- No：37807
- Release Date：2020/04/10 15:10
- Category： Electrical Indicators
Indication values of the main body is different from an obtained value through MODBUS RTU/ TCP (ME96SS series).

Please check the register addresses. The register address for the present value of the power factor of each phase is “0789”. There are the register addre... More Details >>
- No：22191
- Release Date：2018/08/27 16:41
- Category： Electrical Indicators

21-30 of Total 57

Inquiries

page top