You can set the parameters of the FL-net interface module with the data operation of the intelligent function module. Fo

Turn off the drive contact of the WR3A instruction.

Connectors are sold separately. There are two types of connectors: connector for flat cable and connector for bulk wire.

The FX5 CPU module does not support CAN communication.

This function allows you to select the operation to be performed when the FX5-ENET(MQTT client) reconnects to the MQTT

The MQTT communication function cannot publish and subscribe at the same time. A program for the MQTT communication fun

No, there is no function to resend all the data that could not be sent. By setting Retain and QoS from FB, it is possibl

The batch setting of PDO mapping sets the default PDO mapping for all device stations that support PDO mapping. *Note th

The FX5U CPU module has a lineup of up to 80 point. The following configuration is recommended when replacing the FX3U-1

It is not possible to connect multiple devices with different communication speeds and parities.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Controllers

Programmable Automation Controllers MELSEC(28)

MELSEC MX Controller MX-R Model
MELSEC MX Controller MX-F Model(28)
MELSEC MX Controller Engineering Software
Programmable Controllers MELSEC(1731)

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(672)
MELSEC-Q Series(213)
MELSEC-L Series(105)
MELSEC-F Series(457)
Network related products(110)
Engineering Software(129)

Motion Controllers(414)

MELSEC iQ-R Series(73)
MELSEC iQ-F Series(29)
MELSEC-Q Series(247)
MELSEC-L Series(64)
Engneering software(1)

FAQ within [ Controllers ]

311-320 of Total 1123

prev 32 / 113page next

FL-net setting of GX Works2

You can set the parameters of the FL-net interface module with the data operation of the intelligent function module. For details and operation procedure of... More Details >>
- No：23084
- Release Date：2018/09/03 17:31
- Update：2018/09/26 13:19
- Category： Network related products
How to stop D/A conversion while the WR3A (Write to Dedicated Analog Block) instruction is being executed in the FX2N-2DA (analog output)

Turn off the drive contact of the WR3A instruction. More Details >>
- No：24872
- Release Date：2019/04/15 08:06
- Category： MELSEC-F Series , Analog Control
Connectors for FX3UC series

Connectors are sold separately. There are two types of connectors: connector for flat cable and connector for bulk wire. Select connectors suitable for your ... More Details >>
- No：24970
- Release Date：2019/04/23 07:19
- Category： MELSEC-F Series , Accessories
Regarding CAN Communication

The FX5 CPU module does not support CAN communication. More Details >>
- No：39286
- Release Date：2023/02/13 15:36
- Category： MELSEC iQ-F Series , Network/Communication
Regarding the clean session function of MQTT communication function

This function allows you to select the operation to be performed when the FX5-ENET(MQTT client) reconnects to the MQTT broker after communication has been ... More Details >>
- No：40054
- Release Date：2023/08/25 09:02
- Category： MELSEC iQ-F Series , Network/Communication
Regarding simultaneous execution of the MQTT communication function

The MQTT communication function cannot publish and subscribe at the same time. A program for the MQTT communication function is created using FB, but it c... More Details >>
- No：44345
- Release Date：2024/03/27 15:25
- Category： MELSEC iQ-F Series , Network/Communication
Regarding the MQTT communication function retransmission function

No, there is no function to resend all the data that could not be sent. By setting Retain and QoS from FB, it is possible to resend only the latest message. More Details >>
- No：44368
- Release Date：2024/03/27 16:56
- Category： MELSEC iQ-F Series , Network/Communication
Regarding understanding the difference between "Batch Setting of PDO Mapping" and "PDO Mapping Setting".

The batch setting of PDO mapping sets the default PDO mapping for all device stations that support PDO mapping. *Note that in the batch setting of PDO mappi... More Details >>
- No：44476
- Release Date：2024/07/02 19:06
- Category： MELSEC iQ-F Series , Network/Communication
Regarding replacement from 128 point type of FX3U

The FX5U CPU module has a lineup of up to 80 point. The following configuration is recommended when replacing the FX3U-128MR/ES. Recommended alternative (1... More Details >>
- No：44617
- Release Date：2024/11/28 16:13
- Category： MELSEC iQ-F Series , CPU Module
Regarding protocol mixing in Serial Communication

It is not possible to connect multiple devices with different communication speeds and parities. More Details >>
- No：45480
- Release Date：2025/11/12 13:54
- Category： MELSEC iQ-F Series , CPU Module , Network/Communication

311-320 of Total 1123

Inquiries

page top