The MODE switch can set the following modes.- 0 to 4: Online mode- 5 to 9: Line test mode- A to E: Hardware test modeEac

The data link status is stored in SW80 to SW83.Each bit corresponds to a station number and a bit turns ON if the corres

Specify the target axes during operation, and execute the following speed change request instruction. (1) Motion SFC pro

Up to two of the following optional communication equipment, including the FX3U-ENET-ADP (for Ethernet communications),

GX Works2 with Ver. 1.87R or later is required.

The thickness of wire should be 2 square millimeters or more, and class D grounding (grounding resistance: 100 Ω or less

The constant operation processing time can be achieved by using constant scan mode. Refer to the programming manual of t

Whether the latch range is set by default is different. ・Latch (1) — Latch range is set by default. This can be changed

It can be changed. It is now possible to write to the address (user unit, pulse unit) by the DHCMOV command. However, wr

The control response parameter can set the response to the target value (SV) of PID control as either "normal" or "fast"

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Controllers

Programmable Automation Controllers MELSEC(28)

MELSEC MX Controller MX-R Model
MELSEC MX Controller MX-F Model(28)
MELSEC MX Controller Engineering Software
Programmable Controllers MELSEC(1731)

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(672)
MELSEC-Q Series(213)
MELSEC-L Series(105)
MELSEC-F Series(457)
Network related products(110)
Engineering Software(129)

Motion Controllers(414)

MELSEC iQ-R Series(73)
MELSEC iQ-F Series(29)
MELSEC-Q Series(247)
MELSEC-L Series(64)
Engneering software(1)

FAQ within [ Controllers ]

841-850 of Total 1123

prev 85 / 113page next

MODE switch setting for QJ61BT11N

The MODE switch can set the following modes.- 0 to 4: Online mode- 5 to 9: Line test mode- A to E: Hardware test modeEach mode in ascending order of set valu... More Details >>
- No：23025
- Release Date：2018/09/03 17:31
- Category： Network related products
How to check link errors in CC-Link slave stations

The data link status is stored in SW80 to SW83.Each bit corresponds to a station number and a bit turns ON if the corresponding station causes a data link er... More Details >>
- No：23031
- Release Date：2018/09/03 17:31
- Category： Network related products
Speed change during operation

Specify the target axes during operation, and execute the following speed change request instruction. (1) Motion SFC program Speed change request CHGV, CHGVS... More Details >>
- No：23574
- Release Date：2018/09/14 15:09
- Category： Q17nDSCPU , Q170MSCPU
Using the FX3U-ENET-ADP and the RS-232C/RS-485 together (FX3U/FX3UC series)

Up to two of the following optional communication equipment, including the FX3U-ENET-ADP (for Ethernet communications), can be used for the FX3U/FX3UC series... More Details >>
- No：24686
- Release Date：2019/02/22 11:40
- Update：2019/02/22 15:16
- Category： MELSEC-F Series , Main Unit , Network/Communication
Settings for the FX3U-ENET-ADP

GX Works2 with Ver. 1.87R or later is required.　 More Details >>
- No：24781
- Release Date：2019/02/27 16:10
- Category： MELSEC-F Series , Engineering Software , Network/Communication
Thickness of ground wire

The thickness of wireshould be2 square millimeters or more, andclass D grounding (grounding resistance: 100 Ω or less) should be performed. More Details >>
- No：24899
- Release Date：2019/04/15 11:30
- Category： MELSEC-F Series , Main Unit
Operation processing time of the programmable controller

The constant operation processing time can be achieved by using constant scan mode. Refer to the programming manual of the programmable controller used. More Details >>
- No：24997
- Release Date：2019/04/23 10:38
- Category： MELSEC-F Series , Engineering Software , Main Unit
Regarding the differences between Latches (1) and (2)

Whether the latch range is set by default is different. ・Latch (1) — Latch range is set by default. This can be changed at any time. ・Latch (2) — No latch ... More Details >>
- No：39351
- Release Date：2023/02/15 13:08
- Update：2024/08/19 09:54
- Category： MELSEC iQ-F Series , CPU Module , Engineering Software
Regarding changing the current address (user unit, pulse unit)

It can be changed. It is now possible to write to the address (user unit, pulse unit) by the DHCMOV command. However, writing is disabled during positioning... More Details >>
- No：39356
- Release Date：2023/02/15 13:03
- Category： MELSEC iQ-F Series , CPU Module , Motion/Positioning
Regarding Control response parameter of built-in PID Control of CPU Module

The control response parameter can set the response to the target value (SV) of PID control as either "normal" or "fast". The difference is as follows. (1)W... More Details >>
- No：44653
- Release Date：2025/03/18 10:23
- Category： MELSEC iQ-F Series , CPU Module , Analog

841-850 of Total 1123

Inquiries

page top