The latch range can be set arbitrarily by the customer. The settings can be found in the memory/device settings of CPU p

The following ranges overlap. Or the range of file register (R) used has been exceeded. Check whether the file register

No, there is no function to resend all the data that could not be sent. By setting Retain and QoS from FB, it is possib

It's possible. For the firmware and software versions of the corresponding CPU units, refer to the respective manuals.

They can be used together. * 14/24-point type FX3G series main unit ･ An expansion board can be connected to BD1 (1st

Yes, it is possible. Write a new value to the operation speed change value (BFM#56, #55) during the positioning operatio

GX Works2 with Ver. 1.90U or later can be used for the setting of the FX3U-ENET-ADP.

The FX3U-ENET-L does not support the DHCP function. Set the fixed IP address using FX Configurator-EN-L. (FX Configurato

When a coil of the high-speed counter or an interrupt pointer is programmed, the programmable controller system adjusts

Data are received on a received data count basis. If there is no receive complete code and variable length data is recei

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Controllers

Programmable Automation Controllers MELSEC(28)

MELSEC MX Controller MX-R Model
MELSEC MX Controller MX-F Model(28)
MELSEC MX Controller Engineering Software
Programmable Controllers MELSEC(1702)

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(643)
MELSEC-Q Series(213)
MELSEC-L Series(105)
MELSEC-F Series(457)
Network related products(110)
Engineering Software(129)

Motion Controllers(414)

MELSEC iQ-R Series(73)
MELSEC iQ-F Series(29)
MELSEC-Q Series(247)
MELSEC-L Series(64)
Engneering software(1)

FAQ within [ Controllers ]

871-880 of Total 1110

prev 88 / 111page next

Regarding the range of latch devices

The latch range can be set arbitrarily by the customer. The settings can be found in the memory/device settings of CPU parameters. To back up the link regist... More Details >>
- No：22297
- Release Date：2018/08/30 13:55
- Category： MELSEC iQ-F Series , CPU Module
Regarding Error code of FX5-ENET Mail send FB: H210

The following ranges overlap. Or the range of file register (R) used has been exceeded. Check whether the file register (R) is exceeded or not. ・area of de... More Details >>
- No：44608
- Release Date：2024/11/28 16:11
- Category： MELSEC iQ-F Series , Network/Communication
Regarding the MQTT communication function retransmission function

No, there is no function to resend all the data that could not be sent. By setting Retain and QoS from FB, it is possible to resend only the latest message. More Details >>
- No：44368
- Release Date：2024/03/27 16:56
- Category： MELSEC iQ-F Series , Network/Communication
Regarding Data Logging File Storage Format

It's possible. For the firmware and software versions of the corresponding CPU units, refer to the respective manuals. More Details >>
- No：39308
- Release Date：2023/02/13 16:44
- Update：2023/02/14 09:01
- Category： MELSEC iQ-F Series , CPU Module
Connection of expansion boards and a display module to FX3G series main unit

They can be used together. * 14/24-point type FX3G series main unit ･ An expansion board can be connected to BD1 (1st position) and a display module can be... More Details >>
- No：24985
- Release Date：2019/04/23 07:22
- Category： MELSEC-F Series , Main Unit
Operation speed change during a positioning operation of the FX3U-1PG

Yes, it is possible. Write a new value to the operation speed change value (BFM#56, #55) during the positioning operation. * After the operation speed chang... More Details >>
- No：24927
- Release Date：2019/04/17 11:42
- Category： MELSEC-F Series , Positioning Control
Setting of the FX3U-ENET-ADP Ethernet communication special adapter

GX Works2 with Ver. 1.90U or later can be used for the setting of the FX3U-ENET-ADP.　 More Details >>
- No：24875
- Release Date：2019/04/15 08:06
- Category： MELSEC-F Series , Network/Communication
Support of the DHCP (Dynamic Host Configuration Protocol) function by the FX3U-ENET-L (for Ethernet communications)

The FX3U-ENET-L does not support the DHCP function. Set the fixed IP address using FX Configurator-EN-L. (FX Configurator-EN-L can be downloaded from Mitsubi... More Details >>
- No：24869
- Release Date：2019/04/15 08:06
- Category： MELSEC-F Series
Input filter adjustment when a high-speed counter or the interrupt function is used

When a coil of the high-speed counter or an interrupt pointer is programmed, the programmable controller system adjusts the filter constant of the correspond... More Details >>
- No：24867
- Release Date：2019/04/15 08:06
- Category： MELSEC-F Series , High-Speed Counter
Receiving data when no receive complete code is designated (QJ71C24N)

Data are received on a received data count basis. If there is no receive complete code and variable length data is received, the data is received at every no... More Details >>
- No：23038
- Release Date：2018/09/03 17:31
- Category： Network related products

871-880 of Total 1110

Inquiries

page top