Line topologies and star topologies can be mixed.

The fixed data is used for specific codes and character strings such as a command. Setting a device is not required.

Possible causes are as follows.(1) Another master station exists on the same line.(2) Noise is detected on the line at p

The communication between QJ71E71 series modules can be established if READ/WRITE instructions are used.

Check the following signals.- Module error signal : X0- Host data link status signal: X1- Other station data link s

I/O signals and buffer memory addresses need to be changed but data communications can be conducted using a FROM/TO inst

The I/O numbers used for I/O modules and intelligent function modules cannot be used as refresh targets for RX/RY. Use t

You cannot open a program in the file format for GX Works2. When saving a project with GX Works2, save it in the format

You do not have to change the device numbers for each station number in the initial setting procedure registration windo

Yes. The device use list also displays the devices used for specifying digits, such as "K4M0" (including M1, M2, or othe

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Controllers

Programmable Automation Controllers MELSEC(28)

MELSEC MX Controller MX-R Model
MELSEC MX Controller MX-F Model(28)
MELSEC MX Controller Engineering Software
Programmable Controllers MELSEC(1702)

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(643)
MELSEC-Q Series(213)
MELSEC-L Series(105)
MELSEC-F Series(457)
Network related products(110)
Engineering Software(129)

Motion Controllers(414)

MELSEC iQ-R Series(73)
MELSEC iQ-F Series(29)
MELSEC-Q Series(247)
MELSEC-L Series(64)
Engneering software(1)

FAQ within [ Controllers ]

941-950 of Total 1110

prev 95 / 111page next

Mixing line topologies with star topologies in the CC-Link IE Field Network　

Line topologies and star topologies can be mixed. More Details >>
- No：23059
- Release Date：2018/09/03 17:31
- Category： Network related products
Unit of receive data used by the QJ71C24N series pre-defined protocol support function

The fixed data is used for specific codes and character strings such as a command. Setting a device is not required. More Details >>
- No：23049
- Release Date：2018/09/03 17:31
- Category： Network related products
Duplication error in a CC-Link master station

Possible causes are as follows.(1) Another master station exists on the same line.(2) Noise is detected on the line at power on. More Details >>
- No：23044
- Release Date：2018/09/03 17:31
- Category： Network related products
Communication between CPU modules established by QJ71E71

The communication between QJ71E71 series modules can be established if READ/WRITE instructions are used. More Details >>
- No：23036
- Release Date：2018/09/03 17:31
- Category： Network related products
CC-Link signals checked when an error occurs

Check the following signals.- Module error signal : X0- Host data link status signal: X1- Other station data link status signal: X3 More Details >>
- No：23021
- Release Date：2018/09/03 17:31
- Category： Network related products
Using a FROM/TO instruction after AJ71UC24 is replaced with QJ71C24N

I/O signals and buffer memory addresses need to be changed but data communications can be conducted using a FROM/TO instruction and X/Y signals. More Details >>
- No：23017
- Release Date：2018/09/03 17:31
- Category： Network related products
CC-Link master modules' start I/O No. and refresh devices RX/RY

The I/O numbers used for I/O modules and intelligent function modules cannot be used as refresh targets for RX/RY. Use the I/O numbers greater than those use... More Details >>
- No：22997
- Release Date：2018/09/03 17:31
- Category： Network related products
Can I open a program created with GX Works2 in GX Developer?

You cannot open a program in the file format for GX Works2. When saving a project with GX Works2, save it in the format for GX Developer.(This is possible on... More Details >>
- No：22956
- Release Date：2018/09/03 17:31
- Category： Engineering Software
Device numbers set in the initial setting procedure registration window of the CC-Link remote device station

You do not have to change the device numbers for each station number in the initial setting procedure registration window. Example) When the AJ65SBT2B-64A... More Details >>
- No：22949
- Release Date：2018/09/03 17:30
- Update：2018/09/25 11:05
- Category： Engineering Software
Displaying devices in GX Works2

Yes. The device use list also displays the devices used for specifying digits, such as "K4M0" (including M1, M2, or others). More Details >>
- No：22942
- Release Date：2018/09/03 17:30
- Category： Engineering Software

941-950 of Total 1110

Inquiries

page top