It can be cleared with the scan time clear function. You can clear maximum and minimum scan time with GX Works3 Ver. 1.0

The FX3 intelligent function modules cannot be selected from the Element selection window because it does not correspond

CC-Link IE field When a network such as Network Basic is interrupted, the CPU module does not stop and continues to run.

From the GX Works3 settings when the optional battery is installed, it must be set to Installed in the Optional Batter

SD Memory Card Module: FX5-SDCD is required for the following functions. ・Firmware update function ※ 1 ・Memory card fun

It is possible by setting the scaling function or shift function from the parameter settings.

From GXWorks3, use [Online] -[CPU Memory Operation] to initialize. How to check the IP address is as follows. They are s

For TCP protocol of SLMP communication, KeepAlive is fixed and cannot be changed. In the case of UDP protocol, it is fix

You can adjust by setting the constant scan in iQ-F series. Setting procedure: Navigation window > [Parameter] >

You can find it in the Advanced Settings section of GX Works3. Use the following procedure to display the Device (High

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC > MELSEC iQ-F Series > CPU Module

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ CPU Module ]

121-130 of Total 185

prev 13 / 19page next

Regarding clearing the maximum and minimum scan times

It can be cleared with the scan time clear function. You can clear maximum and minimum scan time with GX Works3 Ver. 1.085 P or later or by special relays. More Details >>
- No：39342
- Release Date：2023/02/15 10:05
Regarding selection of FX3 intelligent function modules on the module configuration diagram of GX Works3

The FX3 intelligent function modules cannot be selected from the Element selection window because it does not correspond to the parameter setting of GX Works... More Details >>
- No：22304
- Release Date：2018/08/30 13:55
- Update：2024/08/19 09:50
Regarding CC-Link IE field CPU module status during communication error occurs on CC-Link IE Field Network Basic

CC-Link IE field When a network such as Network Basic is interrupted, the CPU module does not stop and continues to run. When the CC-Link IE Field Network i... More Details >>
- No：44611
- Release Date：2024/11/28 16:11
Regarding settings when the battery is installed

From the GX Works3 settings when the optional battery is installed, it must be set to Installed in the Optional Battery Settings. Use the following proc... More Details >>
- No：44363
- Release Date：2024/03/27 17:09
Regarding the requirement of SD Memory Card module function of FX5S CPU module

SD Memory Card Module: FX5-SDCD is required for the following functions. ・Firmware update function ※ 1 ・Memory card function (SD memory card forced stop,... More Details >>
- No：39338
- Release Date：2023/02/14 17:29
Regarding the digital output of the built-in analog function

It is possible by setting the scaling function or shift function from the parameter settings. More Details >>
- No：22315
- Release Date：2018/08/30 13:55
- Update：2023/06/23 10:46
Regarding initialization procedure

From GXWorks3, use [Online] -[CPU Memory Operation] to initialize. How to check the IP address is as follows. They are stored in special registers SD8492 a... More Details >>
- No：45481
- Release Date：2025/11/12 13:54
Regarding KeepAlive for SLMP Communication

For TCP protocol of SLMP communication, KeepAlive is fixed and cannot be changed. In the case of UDP protocol, it is fixed to not perform a keep-alive check. More Details >>
- No：45477
- Release Date：2025/11/12 13:37
Regarding scan time adjustment for replacing the FX3 Series

You can adjust by setting the constant scan in iQ-F series. Setting procedure: Navigation window > [Parameter] > [Module model name] > [CPU Paramet... More Details >>
- No：44866
- Release Date：2025/03/18 10:24
Regarding checking latch settings

You can find it in the Advanced Settings section of GX Works3. Use the following procedure to display the Device (High Speed) settings. From the GX Wor... More Details >>
- No：44364
- Release Date：2024/03/27 16:05

121-130 of Total 185

Inquiries

page top