Set "[Pr.3] Movement amount per rotation" to "36000000(360.00000degree)", and "[Pr.4] Unit magnification" to "1".The sam

Change the direction with "[PA14] Rotation direction selection/travel direction selection".

It depends on the setting of servo parameter "[PA03] Absolute position detection system" whether the HPR request flag ("

The following shows the setting value details.• 1 to 600: Positioning data No.• 7000 to 7004: Block start designation• 9

Yes. The speed can be changed during JOG operation.Set the new speed with "[Cd.14] New speed value", and then set "[Cd.1

The torque limit value can be changed regardless of JOG operation status.Set the new torque limit value with "[Cd.22] Ne

No, there is no impact on the command speed.However, the actual acceleration/deceleration time are affected by the chang

Refer to "b2: Command in-position flag" of "[Md.31] Status".

Set "[Cd.6] Restart command" to "1".

Set "[Cd.16] Inching movement amount", and turn ON the Forward run JOG start signal or the Reverse run JOG start signal.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Motion Controllers > MELSEC iQ-F Series > Simple Motion Modules

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Simple Motion Modules

FX5SSC(29)

FAQ within [ Simple Motion Modules ]

11-20 of Total 29

prev 2 / 3page next

Electronic gear

Set "[Pr.3] Movement amount per rotation" to "36000000(360.00000degree)", and "[Pr.4] Unit magnification" to "1".The same result is obtained by setting "3600... More Details >>
- No：23586
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Motor rotation direction

Change the direction with "[PA14] Rotation direction selection/travel direction selection". More Details >>
- No：23587
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD74MH
HPR request flag

It depends on the setting of servo parameter "[PA03] Absolute position detection system" whether the HPR request flag ("[Md.31] Status": b3) turns ON or not.... More Details >>
- No：23618
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC
Positioning start No.

The following shows the setting value details.• 1 to 600: Positioning data No.• 7000 to 7004: Block start designation• 9001: Machine home position return• 90... More Details >>
- No：23597
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Speed change during JOG operation

Yes. The speed can be changed during JOG operation.Set the new speed with "[Cd.14] New speed value", and then set "[Cd.15] Speed change request" to "1". More Details >>
- No：23606
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Torque limit value change

The torque limit value can be changed regardless of JOG operation status.Set the new torque limit value with "[Cd.22] New torque value/forward new torque val... More Details >>
- No：23609
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD74MH
Speed limit value

No, there is no impact on the command speed.However, the actual acceleration/deceleration time are affected by the change. More Details >>
- No：23595
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M , QD74MH
Command in-position

Refer to "b2: Command in-position flag" of "[Md.31] Status". More Details >>
- No：23598
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Restart

Set "[Cd.6] Restart command" to "1". More Details >>
- No：23619
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75H
Inching operation

Set "[Cd.16] Inching movement amount", and turn ON the Forward run JOG start signal or the Reverse run JOG start signal. More Details >>
- No：23590
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M

11-20 of Total 29

Inquiries

page top