Error 108 (Start not possible) occurs when a start is requested while a stop signal is ON.Check the "[Md.26] Axis operat

Alarm E7 (Controller forced stop warning) occurs when an forced stop is executed by the Positioning module or the Simple

"M-code" is outputted to turn ON/OFF machine's solenoids or relays according to the start/end of the positioning operati

Error1201 (HPR data incorrect) occurs when the backup data for absolute position restoration is lost.Execute the machine

To reflect the change, set "[PA14] Rotation direction selection/travel direction selection" and cycle the servo amplifie

It depends on the servo error.Some can be cleared by "[Cd.5] Axis error reset" but the other cannot unless the servo amp

Set the torque limit value in "[Cd.101] Torque output setting value" before the positioning start.The values of "[Pr.17]

No. To execute continuous positioning and continuous trajectory control, the same target axes and the same number of con

Set "[Cd.16] Inching movement amount", and turn ON the Forward run JOG start signal or the Reverse run JOG start signal.

Set "[Cd.6] Restart command" to "1".

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Motion Controllers > MELSEC-Q Series > Positioning Modules > QD75MH

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ QD75MH ]

1-10 of Total 33

prev 1 / 4page next

Error 108

Error 108 (Start not possible) occurs when a start is requested while a stop signal is ON.Check the "[Md.26] Axis operation status".If "20: Servo amplifier ... More Details >>
- No：23613
- Release Date：2018/09/14 15:09
Alarm E7

Alarm E7 (Controller forced stop warning) occurs when an forced stop is executed by the Positioning module or the Simple Motion module. The following shows h... More Details >>
- No：23607
- Release Date：2018/09/14 15:09
M-code

"M-code" is outputted to turn ON/OFF machine's solenoids or relays according to the start/end of the positioning operation. The following two modes are sele... More Details >>
- No：23596
- Release Date：2018/09/14 15:09
Error 1201

Error1201 (HPR data incorrect) occurs when the backup data for absolute position restoration is lost.Execute the machine home position return after checking ... More Details >>
- No：23604
- Release Date：2018/09/14 15:09
Servo motor rotation direction

To reflect the change, set "[PA14] Rotation direction selection/travel direction selection" and cycle the servo amplifier or execute a home position return a... More Details >>
- No：23620
- Release Date：2018/09/14 15:09
Axis error reset

It depends on the servo error.Some can be cleared by "[Cd.5] Axis error reset" but the other cannot unless the servo amplifier's power is turned OFF.Refer to... More Details >>
- No：23584
- Release Date：2018/09/14 15:09
Torque limit

Set the torque limit value in "[Cd.101] Torque output setting value" before the positioning start.The values of "[Pr.17] Torque limit setting value" and "[Cd... More Details >>
- No：23583
- Release Date：2018/09/14 15:09
Linear and circular interpolation

No. To execute continuous positioning and continuous trajectory control, the same target axes and the same number of control axes must be specified in the po... More Details >>
- No：23582
- Release Date：2018/09/14 15:09
Inching operation

Set "[Cd.16] Inching movement amount", and turn ON the Forward run JOG start signal or the Reverse run JOG start signal. More Details >>
- No：23590
- Release Date：2018/09/14 15:09
Restart

Set "[Cd.6] Restart command" to "1". More Details >>
- No：23619
- Release Date：2018/09/14 15:09

1-10 of Total 33

Inquiries

page top