Q02(H)CPU-A is the AnUCPU equivalent. When establishing a MELSECNET/10 network, set the refresh parameter with which SB

"The CD terminal is not checked" has been set by default.

Carry out DTR and DSR wiring that returns signals on QJ71C24N(-R2).

Connect terminating resistors to both ends of physical cables.A master station is not necessarily required to be connect

Set the size of buffer memory used for transient transmission (by dedicated instructions) to local stations, the standby

To assure 32-bit data, "Network Range Assignment" of the control station must satisfy the following conditions.(1) The s

X devices will be assigned as follows. (With this setting, 32 points are occupied per station.) - Station No. 1: X10

Short between SDA and RDA and between SDB and RDB, and then connect them to + (Data-A) and - (Data-B) on the external de

Major differences are shown below. - AJ65SBTB1-16DT1 <Input specifications> - Rated input current approx. 5 m

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC > Network related products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ Network related products ]

91-100 of Total 110

prev 10 / 11page next

About network parameters when building MELSECNET/10 with Q02HCPU-A

Q02(H)CPU-A is the AnUCPU equivalent. When establishing a MELSECNET/10 network, set the refresh parameter with which SB/SW data is transferred to "Y/D" or o... More Details >>
- No：23005
- Release Date：2018/09/03 17:31
- Update：2018/09/26 14:42
CD terminal setting of the QJ71C24N

"The CD terminal is not checked" has been set by default. More Details >>
- No：23065
- Release Date：2018/09/03 17:31
Connecting QJ71C24N to an external device that has no DTR signal

Carry out DTR and DSR wiring that returns signals on QJ71C24N(-R2). More Details >>
- No：23039
- Release Date：2018/09/03 17:31
Connecting terminating resistors for CC-Link communication

Connect terminating resistors to both ends of physical cables.A master station is not necessarily required to be connected to either end of its network. More Details >>
- No：23046
- Release Date：2018/09/03 17:31
Intelligent Buffer Select of the CC-Link parameter

Set the size of buffer memory used for transient transmission (by dedicated instructions) to local stations, the standby master station, and intelligent devi... More Details >>
- No：22977
- Release Date：2018/09/03 17:31
32-bit data assurance

To assure 32-bit data, "Network Range Assignment" of the control station must satisfy the following conditions.(1) The start device No. of LB is a multiple o... More Details >>
- No：23052
- Release Date：2018/09/03 17:31
Connecting terminating resistors to the sending end and the receiving end in communication of QJ71C24N

Yes. More Details >>
- No：22998
- Release Date：2018/09/03 17:31
Assignment for connecting two CC-Link remote input modules (16-point type) (Remote net Ver.1 mode)

X devices will be assigned as follows. (With this setting, 32 points are occupied per station.) - Station No. 1: X100 to X11F -Station No. 2: X120 to X13... More Details >>
- No：23082
- Release Date：2018/09/03 17:31
- Update：2018/09/26 13:15
RS-485 connection between LJ71C24 and an external device

Short between SDA and RDA and between SDB and RDB, and then connect them to + (Data-A) and - (Data-B) on the external device. More Details >>
- No：23048
- Release Date：2018/09/03 17:31
Difference between AJ65SBTB1-16DT1 and AJ65SBTB1-16DT2

Major differences are shown below. - AJ65SBTB1-16DT1 - Rated input current approx. 5 mA - ON voltage/ON current 15 VDC or higher/3.0 mA or higher - O... More Details >>
- No：22972
- Release Date：2018/09/03 17:31
- Update：2018/09/25 17:04

91-100 of Total 110

Inquiries

page top