For any type of MELSECNET network (II, /10, and H), B and W devices with the same number cannot be used for multiple sta

Use the cables that meet the IEC60793-2-10 Types A1a.1 optical fiber standard. The connectors are LC (duplex) connectors

No, it is unnecessary. Terminating resistors are only required at both ends of the network.

The MODE switch can set the following modes.- 0 to 4: Online mode- 5 to 9: Line test mode- A to E: Hardware test modeEac

A link error has occurred in one of the slave stations in connection.Master station: Check the parameter again.Slave sta

The resistance value is 110 ohm, 1/2 W.

You can set the parameters of the FL-net interface module with the data operation of the intelligent function module. F

The QJ71C24N series modules can be accessed using A-compatible 1C frames, but the following restrictions are imposed. Th

Carry out DTR and DSR wiring that returns signals on QJ71C24N(-R2).

X devices will be assigned as follows. (With this setting, 32 points are occupied per station.) - Station No. 1: X10

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC > Network related products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ Network related products ]

101-110 of Total 110

prev 11 / 11page next

Link register assignments in MELSECNET/10 networks

For any type of MELSECNET network (II, /10, and H), B and W devices with the same number cannot be used for multiple stations as write areas. Following th... More Details >>
- No：22971
- Release Date：2018/09/03 17:31
- Update：2018/09/25 13:24
CC-Link IE Controller cable standard

Use the cables that meet the IEC60793-2-10 Types A1a.1 optical fiber standard. The connectors are LC (duplex) connectors. Two cores are required.The core di... More Details >>
- No：23032
- Release Date：2018/09/03 17:31
- Update：2018/09/27 12:14
Necessity of terminating resistors in CC-Link communication

No, it is unnecessary. Terminating resistors are only required at both ends of the network. More Details >>
- No：22966
- Release Date：2018/09/03 17:31
MODE switch setting for QJ61BT11N

The MODE switch can set the following modes.- 0 to 4: Online mode- 5 to 9: Line test mode- A to E: Hardware test modeEach mode in ascending order of set valu... More Details >>
- No：23025
- Release Date：2018/09/03 17:31
What makes the ERR LED flash in a CC-Link network

A link error has occurred in one of the slave stations in connection.Master station: Check the parameter again.Slave station: Reassess the power supply, the ... More Details >>
- No：23023
- Release Date：2018/09/03 17:31
Terminating resistors for RS-485 communication of QJ71C24N

The resistance value is 110 ohm, 1/2 W. More Details >>
- No：22978
- Release Date：2018/09/03 17:31
- Update：2018/10/03 15:48
FL-net setting of GX Works2

You can set the parameters of the FL-net interface module with the data operation of the intelligent function module. For details and operation procedure of... More Details >>
- No：23084
- Release Date：2018/09/03 17:31
- Update：2018/09/26 13:19
Whether or not MC protocol frames can be used after A1SJ71UC24 is replaced with QJ71C24N

The QJ71C24N series modules can be accessed using A-compatible 1C frames, but the following restrictions are imposed. The access is limited to the devices wi... More Details >>
- No：22970
- Release Date：2018/09/03 17:31
Connecting QJ71C24N to an external device that has no DTR signal

Carry out DTR and DSR wiring that returns signals on QJ71C24N(-R2). More Details >>
- No：23039
- Release Date：2018/09/03 17:31
Assignment for connecting two CC-Link remote input modules (16-point type) (Remote net Ver.1 mode)

X devices will be assigned as follows. (With this setting, 32 points are occupied per station.) - Station No. 1: X100 to X11F -Station No. 2: X120 to X13... More Details >>
- No：23082
- Release Date：2018/09/03 17:31
- Update：2018/09/26 13:15

101-110 of Total 110

Inquiries

page top