X devices will be assigned as follows. (With this setting, 32 points are occupied per station.) - Station No. 1: X10

The QJ71C24N series modules can be accessed using A-compatible 1C frames, but the following restrictions are imposed. Th

Carry out DTR and DSR wiring that returns signals on QJ71C24N(-R2).

The resistance value is 110 ohm, 1/2 W.

A link error has occurred in one of the slave stations in connection.Master station: Check the parameter again.Slave sta

You can set the parameters of the FL-net interface module with the data operation of the intelligent function module. F

No, it is unnecessary. Terminating resistors are only required at both ends of the network.

X and Y assignments are as follows.- X0 to XF- Y10 to Y1F

The CC-Link IE Controller Network is an improved system that has a higher processing speed and a larger data capacity th

Yes.When connecting a GOT, set the mode setting switch of AJ65BT-R2N to "5" (MELSOFT connection mode).

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC > Network related products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ Network related products ]

1-10 of Total 110

prev 1 / 11page next

Assignment for connecting two CC-Link remote input modules (16-point type) (Remote net Ver.1 mode)

X devices will be assigned as follows. (With this setting, 32 points are occupied per station.) - Station No. 1: X100 to X11F -Station No. 2: X120 to X13... More Details >>
- No：23082
- Release Date：2018/09/03 17:31
- Update：2018/09/26 13:15
Whether or not MC protocol frames can be used after A1SJ71UC24 is replaced with QJ71C24N

The QJ71C24N series modules can be accessed using A-compatible 1C frames, but the following restrictions are imposed. The access is limited to the devices wi... More Details >>
- No：22970
- Release Date：2018/09/03 17:31
Connecting QJ71C24N to an external device that has no DTR signal

Carry out DTR and DSR wiring that returns signals on QJ71C24N(-R2). More Details >>
- No：23039
- Release Date：2018/09/03 17:31
Terminating resistors for RS-485 communication of QJ71C24N

The resistance value is 110 ohm, 1/2 W. More Details >>
- No：22978
- Release Date：2018/09/03 17:31
- Update：2018/10/03 15:48
What makes the ERR LED flash in a CC-Link network

A link error has occurred in one of the slave stations in connection.Master station: Check the parameter again.Slave station: Reassess the power supply, the ... More Details >>
- No：23023
- Release Date：2018/09/03 17:31
FL-net setting of GX Works2

You can set the parameters of the FL-net interface module with the data operation of the intelligent function module. For details and operation procedure of... More Details >>
- No：23084
- Release Date：2018/09/03 17:31
- Update：2018/09/26 13:19
Necessity of terminating resistors in CC-Link communication

No, it is unnecessary. Terminating resistors are only required at both ends of the network. More Details >>
- No：22966
- Release Date：2018/09/03 17:31
Assigning X and Y signals of AJ65SBTB1-32DT

X and Y assignments are as follows.- X0 to XF- Y10 to Y1F More Details >>
- No：23034
- Release Date：2018/09/03 17:31
Difference between the CC-Link IE Controller Network and a MELSECNET/H network

The CC-Link IE Controller Network is an improved system that has a higher processing speed and a larger data capacity than the MELSECNET/H network system (PL... More Details >>
- No：22979
- Release Date：2018/09/03 17:31
- Update：2018/09/25 17:17
Connecting AJ65BT-R2N to a GOT

Yes.When connecting a GOT, set the mode setting switch of AJ65BT-R2N to "5" (MELSOFT connection mode). More Details >>
- No：23047
- Release Date：2018/09/03 17:31

1-10 of Total 110

Inquiries

page top