Reverse connection is possible (connection of load side terminal as powerside and power side terminal as load side). How

At ambient temperature 40℃, the rated voltage (frequency) is applied to acontrol coil, and after temperature rise and sa

SD-T12 to T32 and SD-N600, N800 type operation coil terminals have polarity. Connect terminal mumber A1 (+) to the po

It is a general starting method that applies full voltage to a motor in orderto start and stop. It is also called Full v

It is necessary to change the wires connected by solder to the board of theDL circuit since the wire length is short. Th

For other coil designation, it can be calculated as below.1. For S-T* and S-N* type (AC operation type)(1) Input (Instan

It is utilization category specified in IEC 60947-4-1. AC-3 category is usedfor starting a motor or stopping during oper

The maximum ambient temparature for US-N/K/H type is 60℃ and theycan not be used with more than 60℃. If the temparature

You must not desassemble it since mechanical latched type has beenadjusted and tested at our factory.

In the withstand voltage test, 2500V is applied for 1 min. The appliedlocation is as follows.1. Between the conductive p

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Low-voltage Power Distribution Products > Contactors and Motor Starters > Motor Starters

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ Motor Starters ]

21-30 of Total 142

prev 3 / 15page next

About Low-voltage Power Distribution Products

Reverse connection is possible (connection of load side terminal as powerside and power side terminal as load side). However, it is necessary toinstall a mag... More Details >>
- No：23286
- Release Date：2018/09/12 15:11
About Low-voltage Power Distribution Products

At ambient temperature 40℃, the rated voltage (frequency) is applied to acontrol coil, and after temperature rise and saturation, it can operatewithout any t... More Details >>
- No：23278
- Release Date：2018/09/12 15:11
About Low-voltage Power Distribution Products

SD-T12 to T32 and SD-N600, N800 type operation coil terminals have polarity. Connect terminal mumber A1 (+) to the positive and A2 (-) to the negative sid... More Details >>
- No：23271
- Release Date：2018/09/12 15:11
- Update：2021/04/09 16:21
About Low-voltage Power Distribution Products

It is a general starting method that applies full voltage to a motor in orderto start and stop. It is also called Full voltage starting. More Details >>
- No：23256
- Release Date：2018/09/12 15:11
About Low-voltage Power Distribution Products

It is necessary to change the wires connected by solder to the board of theDL circuit since the wire length is short. Therefore, it is not possible toconnect... More Details >>
- No：23299
- Release Date：2018/09/12 15:11
About Low-voltage Power Distribution Products

For other coil designation, it can be calculated as below.1. For S-T* and S-N* type (AC operation type)(1) Input (Instantaneous, constant) power consumption ... More Details >>
- No：23275
- Release Date：2018/09/12 15:11
About Low-voltage Power Distribution Products

It is utilization category specified in IEC 60947-4-1. AC-3 category is usedfor starting a motor or stopping during operation etc. More Details >>
- No：23241
- Release Date：2018/09/12 15:11
About Low-voltage Power Distribution Products

The maximum ambient temparature for US-N/K/H type is 60℃ and theycan not be used with more than 60℃. If the temparature is more than60℃, you need to consider... More Details >>
- No：23346
- Release Date：2018/09/12 15:12
About Low-voltage Power Distribution Products

You must not desassemble it since mechanical latched type has beenadjusted and tested at our factory. More Details >>
- No：23325
- Release Date：2018/09/12 15:11
About Low-voltage Power Distribution Products

In the withstand voltage test, 2500V is applied for 1 min. The appliedlocation is as follows.1. Between the conductive part and the grounded metal part, and ... More Details >>
- No：23305
- Release Date：2018/09/12 15:11

21-30 of Total 142

Inquiries

page top