For MX Component Ver.5, Ver. 5.000A or later supports the FX5U/FX5UC/FX5UJ CPU modules, and Ver. 5.003D or later support

It is possible to use latch devices or I/O devices (X/Y) for link refresh devices. However, when using I/O devices (X/Y)

Whether the latch range is set by default is different. ・Latch (1) — Latch range is set by default. This can be changed

The keyword protection cannot be forcibly reset. Since only the keyword that has been registered by the user is acceptab

The non-protocol communication can be set by the following two methods: (1) setting parameters using a programming tool,

Minor error 120 occurs in the following case:The zero pass signal (M2406+20n) is OFF when the re-movement to the home po

The error code "2400" is "FILE SET ERROR".It may be determined as the cause of the error that the file that has been spe

A fixed scan execution type program is a program executed at specified time intervals. This type of programs, unlike int

Follow the procedure below.(1)Eliminate the error cause.(2) Store the error code to be cleared in SD50.(3)Turn OFF and O

The value depends on the type of cable in use. - Ver.1.10-compatible CC-Link dedicated cables: 110 ohm, 1/2W - CC-Link d

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Controllers

Programmable Automation Controllers MELSEC(28)

MELSEC MX Controller MX-R Model
MELSEC MX Controller MX-F Model(28)
MELSEC MX Controller Engineering Software
Programmable Controllers MELSEC(1731)

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(672)
MELSEC-Q Series(213)
MELSEC-L Series(105)
MELSEC-F Series(457)
Network related products(110)
Engineering Software(129)

Motion Controllers(414)

MELSEC iQ-R Series(73)
MELSEC iQ-F Series(29)
MELSEC-Q Series(247)
MELSEC-L Series(64)
Engneering software(1)

FAQ within [ Controllers ]

121-130 of Total 1123

prev 13 / 113page next

Regarding communication with MX Component

For MX Component Ver.5, Ver. 5.000A or later supports the FX5U/FX5UC/FX5UJ CPU modules, and Ver. 5.003D or later supports the FX5S CPU module. Also, both se... More Details >>
- No：22328
- Release Date：2018/08/30 13:55
- Update：2023/02/15 13:07
- Category： MELSEC iQ-F Series , CPU Module , Engineering Software , Network/Communication
Regarding the link refresh settings of FX5-CCL-MS

It is possible to use latch devices or I/O devices (X/Y) for link refresh devices. However, when using I/O devices (X/Y), use I/O numbers (such as X1000 ~/Y... More Details >>
- No：22308
- Release Date：2018/08/30 13:55
- Update：2023/06/23 10:37
- Category： MELSEC iQ-F Series , CPU Module , Engineering Software , Network/Communication
Regarding the differences between Latches (1) and (2)

Whether the latch range is set by default is different. ・Latch (1) — Latch range is set by default. This can be changed at any time. ・Latch (2) — No latch ... More Details >>
- No：39351
- Release Date：2023/02/15 13:08
- Update：2024/08/19 09:54
- Category： MELSEC iQ-F Series , CPU Module , Engineering Software
Keyword protection of the MELSEC-F series

The keyword protection cannot be forcibly reset. Since only the keyword that has been registered by theuser is acceptable, please take measures to ensure th... More Details >>
- No：24784
- Release Date：2019/02/27 16:27
- Category： MELSEC-F Series , Engineering Software , Main Unit
Communication setting methods when the FX3U-232-BD is used

The non-protocol communication can be set by the following two methods: (1) setting parameters using a programming tool, such as GX Works2, or (2) writing da... More Details >>
- No：24773
- Release Date：2019/02/27 15:24
- Category： MELSEC-F Series , Engineering Software , Network/Communication
Minor error120

Minor error 120 occurs in the following case:The zero pass signal (M2406+20n) is OFF when the re-movement to the home position is performed by proximity dog,... More Details >>
- No：23559
- Release Date：2018/09/14 15:09
- Category： Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Error code "2400" in QCPU

The error code "2400" is "FILE SET ERROR".It may be determined as the cause of the error that the file that has been specified by a parameter does not exist.... More Details >>
- No：22703
- Release Date：2018/09/03 17:29
- Category： MELSEC-Q Series
Fixed scan execution type (program setting item)

A fixed scan execution type program is a program executed at specified time intervals. This type of programs, unlike interrupt programs, can be interrupted i... More Details >>
- No：22617
- Release Date：2018/09/03 17:29
- Category： MELSEC-Q Series
How to clear errors

Follow the procedure below.(1)Eliminate the error cause.(2) Store the error code to be cleared in SD50.(3)Turn OFF and ON SM50.(4) The error is cleared. More Details >>
- No：22613
- Release Date：2018/09/03 17:29
- Category： MELSEC-Q Series
Resistor value for CC-Link cables

The value depends on the type of cable in use. - Ver.1.10-compatible CC-Link dedicated cables: 110 ohm, 1/2W - CC-Link dedicated cables (Version 1.00): 110... More Details >>
- No：22983
- Release Date：2018/09/03 17:31
- Update：2018/10/03 14:42
- Category： Network related products

121-130 of Total 1123

Inquiries

page top