The following shows the initialization procedure. (1) Turn OFF the PLC ready flag. (2) Turn ON "[Cd.2] Parameter initia

The BUSY signal turns ON even when position control of movement amount "0" is executed.However, since the ON time is sho

A comparison result is held even after the command input turns off. The remaining comparison result can be cleared by us

It is available as a repair part. Please consult with local Mitsubishi Electric representative.

Ver.3.10 or later is applicable. (GX Works2 with Ver.1.73B or later is applicable.) The version of the main unit can be

The station number setting is not required for non-protocol communication.

Yes, it is possible. Set a new value for the target address to the target address change value (BFM#54, #53) during the

The built-in Ethernet port on the FX5 CPU module does not support EtherNet/IP communication. Use FX5-ENET/IP.

In the case of positioning control and OPR control, there are three ways to start positioning: (1)[cd. 184] Turn on t

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Controllers

Programmable Controllers MELSEC(1702)

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(643)
MELSEC-Q Series(213)
MELSEC-L Series(105)
MELSEC-F Series(457)
Network related products(110)
Engineering Software(129)
Motion Controllers(414)

MELSEC iQ-R Series(73)
MELSEC iQ-F Series(29)
MELSEC-Q Series(247)
MELSEC-L Series(64)
Engneering software(1)

FAQ within [ Controllers ]

831-840 of Total 1082

prev 84 / 109page next

Parameter initialization

The following shows the initialization procedure. (1) Turn OFF the PLC ready flag. (2) Turn ON "[Cd.2] Parameter initialization request". [QD75M, QD75MH, LD... More Details >>
- No：23602
- Release Date：2018/09/14 15:09
- Category： QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
BUSY signal

The BUSY signal turns ON even when position control of movement amount "0" is executed.However, since the ON time is short, the ON status may not be detected... More Details >>
- No：23612
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M , QD74MH
Comparison result of the CMP instruction

A comparison result is held even after the command input turns off. The remaining comparison result can be cleared by using the RST or ZRST instruction. More Details >>
- No：24692
- Release Date：2019/02/27 08:56
- Category： MELSEC-F Series
Cable provided with the FX2N series extension unit

It is available as a repair part. Please consult with localMitsubishi Electric representative. More Details >>
- No：24916
- Release Date：2019/04/17 11:40
- Category： MELSEC-F Series , Main Unit , I/O Extension
Supported versions of the FX3U/FX3UC series main units for the CC-Link parameter settings using GX Works2

Ver.3.10 or later is applicable. (GX Works2 with Ver.1.73B or later is applicable.) The version of the main unit can be checked with the last three digits of... More Details >>
- No：24918
- Release Date：2019/04/17 11:40
- Category： MELSEC-F Series , Main Unit
Station number setting in the "PLC System(2)" tab of PLC Parameter setting on GX Developer when non-protocol communication is performed

The station number setting is not required for non-protocol communication. More Details >>
- No：24948
- Release Date：2019/04/18 14:27
- Category： MELSEC-F Series , Main Unit , Network/Communication
Target address change during the positioning operation in the FX3U-1PG

Yes, it is possible. Set a new value for the target address to the target address change value (BFM#54, #53) during the positioning operation. 　　 * The targ... More Details >>
- No：24986
- Release Date：2019/04/23 07:22
- Category： MELSEC-F Series , Positioning Control
Regarding EtherNet/IP Communications

The built-in Ethernet port on the FX5 CPU module does not support EtherNet/IP communication. Use FX5-ENET/IP. More Details >>
- No：39319
- Release Date：2023/02/14 08:57
- Category： MELSEC iQ-F Series , CPU Module , Network/Communication
Regarding converting FBD/LD Projects

It can't be converted. More Details >>
- No：39328
- Release Date：2023/02/14 09:05
- Category： MELSEC iQ-F Series , CPU Module , Engineering Software
Regarding how to start positioning

In the case of positioning control and OPR control, there are three ways to start positioning: (1)[cd. 184] Turn on the positioning start signal. (2)Exec... More Details >>
- No：39360
- Release Date：2023/01/12 17:19
- Category： MELSEC iQ-F Series , Motion/Positioning

831-840 of Total 1082

Inquiries

page top