"M-code" is outputted to turn ON/OFF machine's solenoids or relays according to the start/end of the positioning operati

Set "[Pr.3] Movement amount per rotation" to "36000000(360.00000degree)", and "[Pr.4] Unit magnification" to "1".The sam

Set "[Cd.17] JOG speed" before starting the operation.When changing the speed during the operation, change it to the new

Change the direction with "[PA14] Rotation direction selection/travel direction selection".

Yes. The speed can be changed during JOG operation.Set the new speed with "[Cd.14] New speed value", and then set "[Cd.1

No, there is no impact on the command speed.However, the actual acceleration/deceleration time are affected by the chang

The BUSY signal turns ON even when position control of movement amount "0" is executed.However, since the ON time is sho

To reflect the change, set "[PA14] Rotation direction selection/travel direction selection" and cycle the servo amplifie

Alarm E7 (Controller forced stop warning) occurs when an forced stop is executed by the Positioning module or the Simple

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Motion Controllers > MELSEC-Q Series

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

MELSEC-Q Series

Positioning Modules(74)

QD75M(29)
QD75MH(33)
QD75H(1)
QD74MH(11)

FAQ within [ MELSEC-Q Series ]

51-59 of Total 59

prev 6 / 6page next

M-code

"M-code" is outputted to turn ON/OFF machine's solenoids or relays according to the start/end of the positioning operation. The following two modes are sele... More Details >>
- No：23596
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Electronic gear

Set "[Pr.3] Movement amount per rotation" to "36000000(360.00000degree)", and "[Pr.4] Unit magnification" to "1".The same result is obtained by setting "3600... More Details >>
- No：23586
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
JOG speed

Set "[Cd.17] JOG speed" before starting the operation.When changing the speed during the operation, change it to the new speed with the speed change function. More Details >>
- No：23581
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Motor rotation direction

Change the direction with "[PA14] Rotation direction selection/travel direction selection". More Details >>
- No：23587
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD74MH
Speed change during JOG operation

Yes. The speed can be changed during JOG operation.Set the new speed with "[Cd.14] New speed value", and then set "[Cd.15] Speed change request" to "1". More Details >>
- No：23606
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Speed limit value

No, there is no impact on the command speed.However, the actual acceleration/deceleration time are affected by the change. More Details >>
- No：23595
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M , QD74MH
BUSY signal

The BUSY signal turns ON even when position control of movement amount "0" is executed.However, since the ON time is short, the ON status may not be detected... More Details >>
- No：23612
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M , QD74MH
Servo motor rotation direction

To reflect the change, set "[PA14] Rotation direction selection/travel direction selection" and cycle the servo amplifier or execute a home position return a... More Details >>
- No：23620
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M , QD74MH
Alarm E7

Alarm E7 (Controller forced stop warning) occurs when an forced stop is executed by the Positioning module or the Simple Motion module. The following shows h... More Details >>
- No：23607
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH

51-59 of Total 59

Inquiries

page top