Refer to "b2: Command in-position flag" of "[Md.31] Status".

No, there is no impact on the command speed.However, the actual acceleration/deceleration time are affected by the chang

Set "[Pr.3] Movement amount per rotation" to "36000000(360.00000degree)", and "[Pr.4] Unit magnification" to "1".The sam

No. To execute continuous positioning and continuous trajectory control, the same target axes and the same number of con

Yes. You can check the servo status through the following monitor data. • "[Md.108] Servo status 1" • "[Md.125] Servo st

The following shows the procedure for changing the current value to a new value.(1) Write the new current value to "[Cd.

It depends on the setting of servo parameter "[PA03] Absolute position detection system" whether the HPR request flag ("

Set "[Cd.16] Inching movement amount", and turn ON the Forward run JOG start signal or the Reverse run JOG start signal.

The following shows the initialization procedure. (1) Turn OFF the PLC ready flag. (2) Turn ON "[Cd.2] Parameter initia

Error 1205 (SSCNET communication error) occurs when erroneous data is received from servo amplifier. [When the servo pa

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Motion Controllers > MELSEC-L Series

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

MELSEC-L Series

Simple Motion Modules(64)

LD77MS(32)
LD77MH(32)

FAQ within [ MELSEC-L Series ]

21-30 of Total 32

prev 3 / 4page next

Command in-position

Refer to "b2: Command in-position flag" of "[Md.31] Status". More Details >>
- No：23598
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Speed limit value

No, there is no impact on the command speed.However, the actual acceleration/deceleration time are affected by the change. More Details >>
- No：23595
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M , QD74MH
Electronic gear

Set "[Pr.3] Movement amount per rotation" to "36000000(360.00000degree)", and "[Pr.4] Unit magnification" to "1".The same result is obtained by setting "3600... More Details >>
- No：23586
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Linear and circular interpolation

No. To execute continuous positioning and continuous trajectory control, the same target axes and the same number of control axes must be specified in the po... More Details >>
- No：23582
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Servo status

Yes. You can check the servo status through the following monitor data. • "[Md.108] Servo status 1" • "[Md.125] Servo status 3" (QD77MS, LD77MS, LD77MH) ... More Details >>
- No：23588
- Release Date：2018/09/14 15:09
- Update：2023/03/09 10:02
- Category： QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Current value change

The following shows the procedure for changing the current value to a new value.(1) Write the new current value to "[Cd. 9] New current value".(2) Write "900... More Details >>
- No：23585
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
HPR request flag

It depends on the setting of servo parameter "[PA03] Absolute position detection system" whether the HPR request flag ("[Md.31] Status": b3) turns ON or not.... More Details >>
- No：23617
- Release Date：2018/09/14 15:09
- Category： QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Inching operation

Set "[Cd.16] Inching movement amount", and turn ON the Forward run JOG start signal or the Reverse run JOG start signal. More Details >>
- No：23590
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Parameter initialization

The following shows the initialization procedure. (1) Turn OFF the PLC ready flag. (2) Turn ON "[Cd.2] Parameter initialization request". [QD75M, QD75MH, LD... More Details >>
- No：23602
- Release Date：2018/09/14 15:09
- Category： QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Error 1205

Error 1205 (SSCNET communication error) occurs when erroneous data is received from servo amplifier. [When the servo parameter "[PA14] Rotation direction se... More Details >>
- No：23614
- Release Date：2018/09/14 15:09
- Category： QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M

21-30 of Total 32

Inquiries

page top