The torque limit value can be changed regardless of JOG operation status.Set the new torque limit value with "[Cd.22] Ne

Torque is limited by the lower set value of "[Pr.17] Torque limit setting value" and "[Cd.22] New torque value".When the

There are two ways to start a positioning operation: (1) Set the "[Cd.3] Positioning start No.", and turn ON the positio

Check if 24 VDC power is supplied to "1A7" (pin No.) of the external input signal connector.

Torque is limited by the lower set value of "[Pr.17] Torque limit setting value" and "[Cd.22] New torque value/forward n

Error 2035 (Command frequency error) occurs when the servo amplifier detects a command frequency error. (1) When the com

It depends on the setting of servo parameter "[PA03] Absolute position detection system" whether the HPR request flag ("

No. To execute continuous positioning and continuous trajectory control, the same target axes and the same number of con

Yes. You can check the servo status through the following monitor data. • "[Md.108] Servo status 1" • "[Md.125] Servo

It depends on the servo error.Some can be cleared by "[Cd.5] Axis error reset" but the other cannot unless the servo amp

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Motion Controllers > MELSEC-Q Series > Positioning Modules

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Positioning Modules

FAQ within [ Positioning Modules ]

1-10 of Total 35

prev 1 / 4page next

Torque limit value change

The torque limit value can be changed regardless of JOG operation status.Set the new torque limit value with "[Cd.22] New torque value". More Details >>
- No：23608
- Release Date：2018/09/14 15:09
- Category： QD75M
Torque limit

Torque is limited by the lower set value of "[Pr.17] Torque limit setting value" and "[Cd.22] New torque value".When the current torque reaches the limit, "b... More Details >>
- No：23592
- Release Date：2018/09/14 15:09
- Category： QD75M
Positioning start

There are two ways to start a positioning operation: (1) Set the "[Cd.3] Positioning start No.", and turn ON the positioning start signal. (2) Use the dedica... More Details >>
- No：23593
- Release Date：2018/09/14 15:09
- Category： QD77MS , LD77MS , LD77MH , QD75MH , QD75M
Input/output signal

Check if 24 VDC power is supplied to "1A7" (pin No.) of the external input signal connector. More Details >>
- No：23594
- Release Date：2018/09/14 15:09
- Category： RD77MS , QD77MS , QD75MH , QD75M
Torque limit

Torque is limited by the lower set value of "[Pr.17] Torque limit setting value" and "[Cd.22] New torque value/forward new torque value".When the current tor... More Details >>
- No：23591
- Release Date：2018/09/14 15:09
- Category： QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD74MH
Error 2035

Error 2035 (Command frequency error) occurs when the servo amplifier detects a command frequency error. (1) When the command from the controller is the permi... More Details >>
- No：23616
- Release Date：2018/09/14 15:09
- Category： QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M , QD74MH
HPR request flag

It depends on the setting of servo parameter "[PA03] Absolute position detection system" whether the HPR request flag ("[Md.31] Status": b3) turns ON or not.... More Details >>
- No：23617
- Release Date：2018/09/14 15:09
- Category： QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Linear and circular interpolation

No. To execute continuous positioning and continuous trajectory control, the same target axes and the same number of control axes must be specified in the po... More Details >>
- No：23582
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Servo status

Yes. You can check the servo status through the following monitor data. • "[Md.108] Servo status 1" • "[Md.125] Servo status 3" (QD77MS, LD77MS, LD77MH) ... More Details >>
- No：23588
- Release Date：2018/09/14 15:09
- Update：2023/03/09 10:02
- Category： QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Axis error reset

It depends on the servo error.Some can be cleared by "[Cd.5] Axis error reset" but the other cannot unless the servo amplifier's power is turned OFF.Refer to... More Details >>
- No：23584
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M

1-10 of Total 35

Inquiries

page top