Error 1205 (SSCNET communication error) occurs when erroneous data is received from servo amplifier. [When the servo pa

It depends on the servo error.Some can be cleared by "[Cd.5] Axis error reset" but the other cannot unless the servo amp

No, execute "[Cd.5] Axis error reset" to cancel the error after eliminating the error cause.

Set the torque limit value in "[Cd.101] Torque output setting value" before the positioning start.The values of "[Pr.17]

There are two ways to start a positioning operation: (1) Set the "[Cd.3] Positioning start No.", and turn ON the positio

Torque is limited by the lower set value of "[Pr.17] Torque limit setting value" and "[Cd.22] New torque value/forward n

The BUSY signal turns ON even when position control of movement amount "0" is executed.However, since the ON time is sho

Error 2035 (Command frequency error) occurs when the servo amplifier detects a command frequency error. (1) When the com

Set "[Cd.16] Inching movement amount", and turn ON the Forward run JOG start signal or the Reverse run JOG start signal.

The following shows the initialization procedure. (1) Turn OFF the PLC ready flag. (2) Turn ON "[Cd.2] Parameter initia

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Motion Controllers > MELSEC-Q Series > Positioning Modules

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Positioning Modules

FAQ within [ Positioning Modules ]

21-30 of Total 35

prev 3 / 4page next

Error 1205

Error 1205 (SSCNET communication error) occurs when erroneous data is received from servo amplifier. [When the servo parameter "[PA14] Rotation direction se... More Details >>
- No：23614
- Release Date：2018/09/14 15:09
- Category： QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Axis error reset

It depends on the servo error.Some can be cleared by "[Cd.5] Axis error reset" but the other cannot unless the servo amplifier's power is turned OFF.Refer to... More Details >>
- No：23584
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Warning

No, execute "[Cd.5] Axis error reset" to cancel the error after eliminating the error cause. More Details >>
- No：23580
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Torque limit

Set the torque limit value in "[Cd.101] Torque output setting value" before the positioning start.The values of "[Pr.17] Torque limit setting value" and "[Cd... More Details >>
- No：23583
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Positioning start

There are two ways to start a positioning operation: (1) Set the "[Cd.3] Positioning start No.", and turn ON the positioning start signal. (2) Use the dedica... More Details >>
- No：23593
- Release Date：2018/09/14 15:09
- Category： QD77MS , LD77MS , LD77MH , QD75MH , QD75M
Torque limit

Torque is limited by the lower set value of "[Pr.17] Torque limit setting value" and "[Cd.22] New torque value/forward new torque value".When the current tor... More Details >>
- No：23591
- Release Date：2018/09/14 15:09
- Category： QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD74MH
BUSY signal

The BUSY signal turns ON even when position control of movement amount "0" is executed.However, since the ON time is short, the ON status may not be detected... More Details >>
- No：23612
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M , QD74MH
Error 2035

Error 2035 (Command frequency error) occurs when the servo amplifier detects a command frequency error. (1) When the command from the controller is the permi... More Details >>
- No：23616
- Release Date：2018/09/14 15:09
- Category： QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M , QD74MH
Inching operation

Set "[Cd.16] Inching movement amount", and turn ON the Forward run JOG start signal or the Reverse run JOG start signal. More Details >>
- No：23590
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC , QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M
Parameter initialization

The following shows the initialization procedure. (1) Turn OFF the PLC ready flag. (2) Turn ON "[Cd.2] Parameter initialization request". [QD75M, QD75MH, LD... More Details >>
- No：23602
- Release Date：2018/09/14 15:09
- Category： QD77MS , QD77GF , LD77MS , LD77MH , QD75MH , QD75M

21-30 of Total 35

Inquiries

page top