You cannot select the item while the programmable controller is being monitored. Execute [Close all windows] of [Window

It depends on the setting of servo parameter "[PA03] Absolute position detection system" whether the HPR request flag ("

The FX3U-32BL can be installed to the FX3G/FX3GC series. After installation, select [Battery Mode: Use the battery] on

The data in the special registers SD62 to SD79 change with the following process. - Turn ON the registers with OUT an

The error code "2110" is "SP.UNIT ERROR.". This error may be caused by one of the following factors. (1) The module t

If the L.ERR LED flashes at irregular intervals, it may indicate that no terminating resistor has been connected or the

D200 to D7999 and R0 to R32767 can be latched. D200 to D511 can be set as non-latch areas in parameters. For details o

The error code "2200" is "MISSING PARA.". The causes of the error are described below. (1) The necessary parameter fi

Error 3012 occurs when the multiple CPU setting of PLC CPU (CPU No.1) does not match that of Motion CPU. (1) Check if th

Alarm 2149 (Main circuit OFF warning) occurs when the servo system turns ON with no power supplied to the servo main cir

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Controllers

Programmable Controllers MELSEC(1702)

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(643)
MELSEC-Q Series(213)
MELSEC-L Series(105)
MELSEC-F Series(457)
Network related products(110)
Engineering Software(129)
Motion Controllers(414)

MELSEC iQ-R Series(73)
MELSEC iQ-F Series(29)
MELSEC-Q Series(247)
MELSEC-L Series(64)
Engneering software(1)

FAQ within [ Controllers ]

1021-1030 of Total 1082

prev 103 / 109page next

I cannot select [Transfer Setup] in GX Developer because it is displayed in gray.

You cannot select the item while the programmable controller is being monitored. Execute [Close all windows] of [Window] from the tool bar, and check if Tra... More Details >>
- No：22955
- Release Date：2018/09/03 17:31
- Update：2018/09/25 12:11
- Category： Engineering Software
HPR request flag

It depends on the setting of servo parameter "[PA03] Absolute position detection system" whether the HPR request flag ("[Md.31] Status": b3) turns ON or not.... More Details >>
- No：23618
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC
How to install a battery to FX3G/FX3GC series

The FX3U-32BL can be installed to the FX3G/FX3GC series. After installation, select [Battery Mode: Use the battery] on the FX parameter window of GX Develop... More Details >>
- No：22271
- Release Date：2018/08/30 13:48
- Category： MELSEC-F Series , Main Unit , Accessories
Turning ON/OFF annunciators (F)

The data in the special registers SD62 to SD79 change with the following process. - Turn ON the registers with OUT and SET instructions. - Turn OFF the r... More Details >>
- No：22649
- Release Date：2018/09/03 17:29
- Update：2018/09/21 11:45
- Category： MELSEC-Q Series
Error code "2110" in QCPU

The error code "2110" is "SP.UNIT ERROR.". This error may be caused by one of the following factors. (1) The module that has been specified by a FROM/TO i... More Details >>
- No：22662
- Release Date：2018/09/03 17:29
- Update：2018/09/21 13:48
- Category： MELSEC-Q Series
CC-Link slave station's flashing L.ERR LED

If the L.ERR LED flashes at irregular intervals, it may indicate that no terminating resistor has been connected or the communication is instable due to the ... More Details >>
- No：23001
- Release Date：2018/09/03 17:31
- Category： Network related products
Latch (backup) areas in the data register (D) and extended register (R) of the FX3U/FX3UC series

D200 to D7999 and R0 to R32767 can be latched. D200 to D511 can be set as non-latch areas in parameters. For details on the parameter setting, refer to the... More Details >>
- No：24699
- Release Date：2019/02/27 08:58
- Category： MELSEC-F Series , Engineering Software , Main Unit
Error code "2200" in LCPU

The error code "2200" is "MISSING PARA.". The causes of the error are described below. (1) The necessary parameter file does not exist in all drives. (2) ... More Details >>
- No：22749
- Release Date：2018/09/03 17:29
- Update：2018/09/22 09:12
- Category： MELSEC-L Series
Error 3012

Error 3012 occurs when the multiple CPU setting of PLC CPU (CPU No.1) does not match that of Motion CPU. (1) Check if the multiple CPU setting of the Multipl... More Details >>
- No：23563
- Release Date：2018/09/14 15:09
- Category： Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN
Alarm 2149

Alarm 2149 (Main circuit OFF warning) occurs when the servo system turns ON with no power supplied to the servo main circuit. Review the condition of servo O... More Details >>
- No：23566
- Release Date：2018/09/14 15:09
- Category： Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN

1021-1030 of Total 1082

Inquiries

page top